Topmodel PILATUS TURBO PORTER SCALE ECOTOP Manuel utilisateur

PDF
Document
PILATUS PC-6: Notice + Chat IA & PDF | Fixfr
/

User questions

S B

Robert S.

How to correct flap asymmetry on the Pilatus PC-6?

No votes

To correct flap asymmetry, ensure the servo horn is at neutral with the flap positioned 20 mm downward (the first notch). Adjust the mechanical linkage length by screwing or unscrewing the clevis until alignment is achieved. Recommended travel values are 20 mm for the first notch and 45 mm for the second notch, with a maximum downward travel of 80° to 90°. If mechanical adjustment is insufficient, use the transmitter's electronic settings such as sub-trim or end-point adjustments. Additionally, verify that the flap hinges are correctly glued and aligned.

S B

Robert S.

How to correct flap asymmetry on the Pilatus PC-6?

No votes

With the servo arm at neutral, the flap should be set to a reference position of 20 mm downward. To adjust the alignment, modify the length of the mechanical linkage by screwing or unscrewing the clevis. Additionally, ensure the hinges are correctly glued and aligned. If mechanical adjustment is insufficient, use transmitter electronic settings such as sub-trim or end-point adjustments to equalize the travel on both sides.

S B

Robert S.

How to correct flap asymmetry on a Pilatus PC-6?

No votes

To correct flap asymmetry, set the servo arm to neutral with the flap positioned 20 mm downward (1st notch). Adjust the linkage length by screwing or unscrewing the clevis until the flaps are aligned. Verify symmetry at both recommended positions: 20 mm down (1st notch) and 45 mm down (2nd notch), with a maximum downward throw of 80° to 90°. If the mechanical adjustment is insufficient, verify that the hinges are correctly glued and use the transmitter's sub-trim or end-point adjustments for fine-tuning.

S B

Robert S.

How to correct flap asymmetry on the Pilatus PC-6?

No votes

Flap alignment is adjusted by screwing or unscrewing the clevis to modify the linkage length. With the servo at neutral, the flap must be positioned 20 mm down (1st notch), 45 mm down for the 2nd notch, and reach a maximum travel of 80° to 90°. Ensure that flap hinges are correctly glued. If mechanical adjustment is insufficient, use transmitter sub-trim or end-point settings for fine-tuning.

S B

Robert S.

How to correct flap asymmetry and alignment issues on a Pilatus PC-6?

No votes

Set the servo horn to neutral so the flap is positioned 20 mm downward. Adjust the linkage length by screwing or unscrewing the clevis until the flaps are aligned. Verify the 1st notch at 20 mm and the 2nd notch at 45 mm, ensuring a maximum travel of 80° to 90°. If mechanical adjustment is insufficient, use the transmitter's sub-trim or end-point functions to fine-tune the alignment. Ensure hinges are correctly glued if the travel remains asymmetrical.

S B

Robert S.

How to correct flap asymmetry on the Pilatus PC-6?

No votes

With the servo arm at neutral, the flap should be positioned 20 mm downwards. Adjust the linkage length by screwing or unscrewing the clevis until the flaps are aligned. Verify symmetry at the first notch (20 mm) and second notch (45 mm). If mechanical adjustment is insufficient, use transmitter electronic settings such as sub-trim or end-point adjustments to fine-tune the alignment.

S B

Robert S.

How to correct flap asymmetry on the Pilatus PC-6?

No votes

Set the servo to neutral and adjust the linkage length by screwing or unscrewing the clevis until the flap is 20 mm down. If mechanical adjustment is insufficient, use the transmitter's sub-trim or end-point functions to equalize the sides.

S B

Robert S.

How to correct flap asymmetry on a Pilatus PC-6?

No votes

Set the servo arm to neutral with the flap positioned 20 mm down (1st notch). Adjust the linkage length by screwing or unscrewing the clevis until the flaps are aligned. Verify travel values: 20 mm for the 1st notch, 45 mm for the 2nd notch, and a maximum travel of 80° to 90°. If mechanical adjustments are insufficient, use the transmitter's sub-trim or end-point settings to fine-tune the alignment. Ensure that the hinges are correctly glued to prevent asymmetry.

S B

Robert S.

How to correct flap asymmetry and adjust the flap linkage?

No votes

To correct flap asymmetry, adjust the length of the linkage by screwing or unscrewing the clevis. With the servo at neutral, the flap should be set to 20 mm down (first notch). Ensure that the hinges are correctly glued and aligned. If mechanical adjustment is insufficient, use the transmitter's sub-trim or end-point functions to achieve an alignment of 20 mm for the first notch and 45 mm for the second notch.

Preparing document for printing…
0%