BEDHEAD - 10 Tone
INSTALLATION INSTRUCTIONS
BEDHEAD
+
-
Stage1
Frequency
BEDHEAD
Stage2
Stage3
tone
Description
dB@ 1m
(S2)
(S3)
S2 S3
Tone 1
800/1000Hz @ 0.25 sec Alternating
Tone 2
500/1200Hz @ 0.3Hz 0.5 sec Slow Whoop
85dB(A) @1m
89dB(A) @ 1m
Stage 2 Stage 3
Tone 3
1200/500Hz @ 1Hz - DIN / PFEER P.T.A.P.
Tone 4
Tone 5
544Hz (100mS)/440Hz (400mS) - NF S 32-001
1000Hz Continuous - PFEER Toxic Gas
Tone 6
Tone 7
Tone 8
Tone 9
Tone 10
Tone 8
Tone 5
88dB(A) @ 1m
Tone 1
Tone 1
Tone 8
Tone 8
83dB(A) @ 1m
85dB(A) @ 1m
554Hz
Tone 1
Tone 2
Tone 6
Bell
82dB(A) @1m
Tone 1
Tone 8
800/1000Hz @ 7Hz Sweeping
Tone 5
Tone 1
2400/2900Hz @ 50Hz Sweeping
420Hz @ 0.625 sec Australian Alert
81dB(A) @1m
90dB(A) @ 1m
Tone 5
Tone 1
85dB(A) @ 1m
Tone 10
Tone 5
500-1200Hz 3.75sec /0.25sec. Australian Evac.
90dB(A) @ 1m
Tone 6
Tone 5
Tone 2
Tone 3
Tone 4
Tone 5
Tone 6
Tone 7
Tone 8
Tone 9
Tone 10
Fig 1.
Tone 1
Voltage :
Voltage range :
Current mA :
>90dB(A)@1m
24vdc
10-30vdc
8mA
•Volume Control
•Réglage du volume
•Steuerung der Lautstärke
•Controllo volume
•Controlo do Volume
•Control Volumen
•Vol umen kontrol
•Vo lum ereg eli ng
•Vo lum kon tro ll
•Vo lym kon tro ll
•
•
Tone selection. To select a tone place the pin link in the position shown above (Fig. 1).
•
Tonwahl / Einstellung der Schalter. Zur Wahl eines Tons die Klem menanschlüsse in die angegebenen Positionen
bringen (Fig. 1).
•
Selezione tono / regolazione commutatore. Per selezionare un tono, disporre i collegamenti a cavallotto nelle posizioni
indicate (Fig. 1).
•
Seleção de tons / ajuste dos comutadores. Para seleccionar um tom, coloque as ligações dos pinos na posição mostrada
(Fig.1).
•
Selección Tono / programación interruptores. Para seleccionar un tono colocar las conexiones de los puentes en las
posiciones mostradas (Fig. 1).
•
Toonselectie. Om een toon te s electeren de pinverbinding in de hierboven aangetoonde positie plaatsen (Fig. 1)
•
•
•
Valg af tone. Valg af en tone s ker ved at anbringe stiftforbindelsen i ovenstående position (fig. 1).
Sélection de la tonalité / réglage des commutateurs. Pour sélectionner une tonalité, mettre les socles à broches dans les
positions illustrées (Fig. 1).
Velge tone . For å velge en tone må du plassere stiftleddet i posisjonen som vist ovenfor (fig. 1).
Tonv al. Välj en ton genom att plac era s tiftanslutningen i läget s om visas ovan (fig. 1).
NOTE: Ple ase check factory settings a nd ens ure the cor rect a larm tone is sele cted for your country or application.
ISN2301-A
No liabil ity i s acce pted for an y con sequen ce of the u se of this docume nt. T he tec hnica l spec ifica tion o f thi s unit is
sub ject t o chan ge wi thout notice due to our policy of contin ual product devel opment . All dimen sions are
app roxima te.Thi s uni t is sold su bject to ou r stan dard condit ions of sal e, a c opy o f whic h is a vaila ble on reque st.
Pas op: bij ingebr uikstelling die nt u zich ervan te overtuigen dat de unit op de juiste toon is ingeste ld.
Tel : 0044(0)2087438880
mail : sales@e2s.com
Fax
: 0044(0)2087404200
web : www.e2s.com
">
