Unilamp VOLGA - CV Mode d'emploi

INSTALLATION MANUAL
PRODUCT NAME : VOLGA/1 - CV Ground / Concrete Wall Recess
VOLGA/1 - CC Ground / Concrete Wall Recess
No.
Input
lll
IP68
Glass Temperature
At Ta 50°C
Ordering Code
1. Constant Voltage
24V
2. ( Output from SELV
3. system only)
( ¡ÃÐáÊ俵ŒÍ§ÁÒ
4. ¨Ò¡Ãкºáç´Ñ¹ä¿¿‡Ò
µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂ
5. à¾Õ§෋ҹÑé¹)
6.
9007-4-2-361-91
65.5° C TA40°
9007-A-/6/C/H/U/0/2-429-91
61° C TA40°
9007-A-/6/C/H/U/0/2-2-430-91
61° C TA40°
9007-A-/6/C/H/U/0/2-2-431-91
61° C TA40°
9007-B/C/H/U/0-2-372-91
60° C TA25°
9007-B/C/H/U/0-2-373-91
60° C TA25°
7.
9007-B/C/H/U/0-2-374-91
60° C TA25°
Current
8. Constant
700mA (CC)
9. Constant Current
1200mA (CC)
10.
9008-4-2-355-91
65.5° C TA40°
9008-A/6/C/H/U/0-2-561-91
60° C TA50°
9008-A/6/C/H/U/0-2-562-91
60° C TA50°
11.
9008-A/6/C/H/U/0-2-563-91
60° C TA50°
-
+
1-11
Light Emitting Diodes
(LED)
1
2
108
û70
2.1
2.2
112
Cable length 200 mm.
ÊÒÂä¿ÂÒÇ 200 ÁÁ.
Please note the ground level.
¢ŒÍ¤ÇÃÃÐÇѧ : ¼ÔÇ˹ŒÒ¢Í§µÑÇâ¤Á¡Ñº¼ÔÇ
¾×鹤ÇÃÍÂًã¹ÃйҺà´ÕÂǡѹ
95
Unit:mm.
2 Meters cable pre-wired
from the factory.
ÊÒÂä¿ÂÒÇ2àÁµÃ»ÃСͺÁÒ
¾ÃŒÍÁ¡ÑºµÑÇâ¤Á¨Ò¡âç§Ò¹
105
150x150
50
concrete
20-30cm.
Wire Mesh
Cable conduit
Ø22mm.
85
Gravel
Approx size: 3 4 "
Last Revised On : 25/09/2023 REV.01
1/6
FR-DM-17 REV.03 EFF 15/09/17
3
4
4
7
2
Cable size : 2x1.00 mm. 4.8-6mm.
¢¹Ò´ÊÒÂä¿
Gel-Filled IP68 Connector Cable Diameter
4.8 - 6mm.
Available Separately
à¨Åµ‹ÍÊÒÂ信ѹ¹éíÒIP68,¢¹Ò´ÊÒÂä¿ Ø 4.8-6ÁÁ.
ᡨíÒ˹‹Òµ‹Ò§ËÒ¡
Ordering Code : AUN-CON-0024-00
'See connecting detail on manual.'
´ÙÃÒÂÅÐàÍÕ´·Õè¤Ù‹Á×Í¡ÒõԴ
Installation complete
¡ÒõԴµÑé§àÊÃç¨ÊÁºÙó
Remote driver for 24V system. / For On-Off, DALI system. OD-9007
ä´ÃàÇÍϵԴµÑ駹͡µÑÇâ¤ÁÊíÒËÃѺÃкºä¿ 24V / ÊíÒËÃѺÃкº ແ´-»´ / DALI
Luminaires 1-n
Warning
Please ensure that the led lamp is connected to the driver correctly.
Wrong polarity connection cause a damage to the led lamp and driver.
â»Ã´ÃÐÇѧ¡Òõ‹ÍÊÒÂä¿ÊÅѺ¢ÑéÇ +ºÇ¡ -ź ¨Ò¡ä´ÃàÇÍÏÁÒࢌҷÕèËÅÍ´ LED ËÒ¡µ‹ÍÊÅѺ¢ÑéÇ
¨Ð·íÒãˌä´ÃàÇÍÏáÅÐËÅÍ´ LED à¡Ô´¤ÇÒÁàÊÕÂËÒÂ
Input/ࢌÒ
220-240 V~
L
N
AC
+
DC
+
1
-
+
2
-
+
n
-
-
Output/ÍÍ¡
24 V
( Output from SELV system only)
(¡ÃÐáÊ俵ŒÍ§ÁÒ¨Ò¡Ãкºáç´Ñ¹ä¿¿‡Ò
µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂà¾Õ§෋ҹÑé¹)
Parallel wiring constant voltage
Distance from luminaire to Driver
ÃÐÂзҧ¨Ò¡µÑÇâ¤Á¶Ö§ ä´ÃàÇÍÏ
Luminaire Wattage Maximum number of luminaires
Conductor size / ¢¹Ò´ÊÒÂä¿
¨íҹǹâ¤Á㹡Òõ‹Í
Accessory available separately./ÍØ»¡Ã³àÊÃÔÁ¨íÒ˹‹ÒÂᡵ‹Ò§ËÒ¡
Ordering Code
Product Name
1.00 mm.2
1.50 mm.2
2.00 mm.2
AUN-DRG-0027-00 LED Constant Voltage
Driver 24Vdc 72W.
3.3 W
1-7 luminaire
30 m
50 m
65 m
AUN-DRG-0011-00 LED Constant Voltage
Driver 24Vdc 150W.
3.3 W
1-11 luminaire
30 m
50 m
65 m
AUN-DRG-0024-00 LED Constant Voltage
Driver 24Vdc 200W.
3.3 W
1-13 luminaire
30 m
50 m
70 m
Last Revised On : 25/09/2023 REV.01
2/6
FR-DM-17 REV.03 EFF 15/09/17
For Constant Current 700mA/1200mA (Remote driver) OD-9008
Warning
Please ensure that the led lamp is connected to the driver correctly.
Wrong polarity connection cause a damage to the led lamp and driver.
â»Ã´ÃÐÇѧ¡Òõ‹ÍÊÒÂä¿ÊÅѺ¢ÑéÇ +ºÇ¡ -ź ¨Ò¡ä´ÃàÇÍÏÁÒࢌҷÕèËÅÍ´ LED ËÒ¡µ‹ÍÊÅѺ¢ÑéÇ
¨Ð·íÒãˌä´ÃàÇÍÏáÅÐËÅÍ´ LED à¡Ô´¤ÇÒÁàÊÕÂËÒÂ
L
Input/ࢌÒ
220-240 V~
N
AC
+
-
DC
+
1
-
Output/ÍÍ¡
700mA/1200mA
( Output from SELV system only)
(¡ÃÐáÊ俵ŒÍ§ÁÒ¨Ò¡Ãкºáç´Ñ¹ä¿¿‡Ò
µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂà¾Õ§෋ҹÑé¹)
Distance from luminaire to Driver
ÃÐÂзҧ¨Ò¡µÑÇâ¤Á¶Ö§ ä´ÃàÇÍÏ
Luminaire Wattage Maximum number of luminaires
Conductor size / ¢¹Ò´ÊÒÂä¿
¨íҹǹâ¤Á㹡Òõ‹Í
Accessory available separately./ÍØ»¡Ã³àÊÃÔÁ¨íÒ˹‹ÒÂᡵ‹Ò§ËÒ¡
Ordering Code
Product Name
AUN-GOP-0101-01 LED Constant Current
Driver 700mA 4W. In
IP67 GFR Polymer Box
(On-Off).
AUN-DRG-0012-00 LED Constant Current
Driver 700mA 20W. In
IP67 GFR Polymer Box
(DALI)
AUN-DRG-0007-00 LED Constant Current
Driver 1200mA 6W. In
IP67 GFR Polymer Box
(On-Off).
1.00 mm.2
1.50 mm.2
2.00 mm.2
2.2 W
1 luminaire
55 m
85 m
110 m
2.2 W
1-3 luminaire
55 m
80 m
110 m
3.9 W
1 luminaire
10 m
15 m
20 m
Remark :
ËÁÒÂà˵Ø
1. Installation should be carried out by a qualified
electrician in accordance with appropriate national
wiring regulation.
¡ÒõԴµÑé§â¤Áä¿¿‡ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´Âª‹Ò§ä¿¿‡Ò
·ÕèÁÕ¤ÇÒÁÃٌáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿‡Ò
â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿‡Ò
2. Disconnect the power before changing the lamp.
»´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿
3. For Class1 luminaire, the installation must be
completed with earthing.
ÊíÒËÃѺâ¤Áä¿·ÕèÁ¡Õ Òû‡Í§¡Ñ¹ä¿¿‡ÒÃÑèÇÃдѺ1
¡ÒõԴµÑ駵ŒÍ§µ‹ÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑ´ŒÇÂ
4. Do not exceed the maximum wattage.
ˌÒÁ㪌ËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡Ç‹Ò·ÕèÃÐºØ ËÃ×Í㪌ËÅÍ´¼Ô´»ÃÐàÀ·
Warning :
¢ŒÍ¤ÇÃÃÐÇѧ
1. The manufacturer will not be liable or held responsible
for any incorrect installation, misuse or improper use
and unauthorised modification to the fittings. Failure
to comply with mentioned warning may cause serious
damage or serious injury to persons, animals or
objects. If any modification is required please consult
your dealer for the details.
·Ò§¼ÙŒ¼ÅÔµäÁ‹ÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡
¡ÒõԴµÑé§äÁ‹¶Ù¡ÇÔ¸Õ,㪌§Ò¹¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Á
ã¹·Ø¡¡Ã³Õ«Öè§ ÊÔ觼Դ»¡µÔàËŋҹՌ ÍÒ¨·íÒãˌà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊѵǏ
ÊÔ觢ͧ ËÒ¡ÁÕ¢ŒÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµŒÍ§¡ÒûÃѺᵋ§µÑÇâ¤Á
ãˌàËÁÒÐÊÁ¡Ñº¡ÒÃ㪌§Ò¹¡ÃسҵԴµ‹ÍµÑÇá·¹¨íÒ˹‹ÒÂËÃ×ͼٌ¼ÅÔµ
2. Where damage has occured to the fittings, please
make the replacement with standard parts before use.
㹡óշèÁÕ Õªé¹Ô ʋǹ»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡ÃسÒà»ÅÕè¹
ªÔé¹Ê‹Ç¹ãËÁ‹¡Í‹ ¹¡ÒÃ㪌§Ò¹·Ø¡¤ÃÑé§ à¾×èͤÇÒÁ»ÅÍ´ÀÑÂ
5. Don't touch LED while maintaining or cleaning.
ˌÒÁÊÑÁ¼ÑÊËÅÍ´ LED ¢³ÐºíÒÃاÃÑ¡ÉÒ ËÃ×Í·íÒ¤ÇÒÁÊÐÍÒ´
Last Revised On : 25/09/2023 REV.01
3/6
FR-DM-17 REV.03 EFF 15/09/17
General installation guide ( highly recommended)
¢ŒÍá¹Ð¹íÒ㹡ÒõԴµÑé§
Pic-1
ÃÙ»-1
200-300mm.
Pic-2
ÃÙ»-2
Place the gravel 200-300 mm.depth underneath the casing for water drainage
(Pic-1).Then do the testing by filling water into the casing and let it drain.The
water should be drained out by 30 minutes.
If not,the additional drainage pipe or other system must be applied
(Pic-2)
¤ÇÃÇÒ§¡ŒÍ¹¡ÃǴ㵌¡Å‹Í§½˜§¾×é¹·ÕèÃÐÂÐÅÖ¡»ÃÐÁÒ³ 200-300 ÁÁ. à¾×èͪ‹ÇÂÃкÒÂ
¹éíÒ·Õ跋ÇÁ¢Ñ§µÑÇâ¤Áä¿ ÊÒÁÒö·´Êͺ¡ÒÃÃкÒ¹éíÒâ´Âà·¹éíÒãʋ¡Å‹Í§ãˌàµçÁ
¹éíҨеŒÍ§ÃкÒÂÍÍ¡ËÁ´ÀÒÂã¹àÇÅÒ 30¹Ò·Õ ËÒ¡äÁ‹à»š¹µÒÁ¹Ñ鹤ÇÃÁÕ¡Òõ‹Í
·‹ÍÃкÒ¹éíÒà¾ÔèÁàµÔÁ
Cable conduit
·‹ÍÊÒÂä¿
Water drainage
conduit.
·‹Í¹éíÒ·Ôé§
Installation should not be done under high humidity environment i.e.
rainy day or after the rain,foggy weather....ect.
äÁ‹¤ÇõԴµÑé§â¤Áä¿ã¹ª‹Ç§·ÕèÁÕ¤ÇÒÁª×é¹Ê٧ઋ¹ Çѹ·Õè½¹µ¡µÅÍ´ËÃ×͵ԴµÑé§ËÅѧ
½¹ËÂØ´µ¡à¾ÃÒШзíÒãˌ¤ÇÒÁª×鹶١¢Ñ§änj㹵ÑÇâ¤Áä¿ËÅѧ¨Ò¡¹Ñ鹨Ðà¡Ô´¡ÒÃ
¤Çºá¹‹¹à»š¹ÅÐÍͧËÃ×ÍË´¹éíÒà¡ÒеԴºÃÔàdz㵌¡ÃШ¡ÀÒÂã¹µÑÇâ¤Áä¿
Do not let the exposed part of the fittings be covered by the soil,dried weed or
foliage as well as corrosive or aggressive substancechemicals.
Í‹һŋÍÂãˌÁÕÊÔè§Ê¡»Ã¡àª‹¹ àÈÉ´Ô¹ ãºäÁŒ ËÃ×Í
Ë­ŒÒáˌ§ÃÇÁ¶Ö§à¤ÁÕ·Õè໚¹ÊÒÃ-¡Ñ´¡Ã‹Í¹ÁÒ»¡¤ÅØÁÊÐÊÁºÃÔàdz˹ŒÒ¾×é¹¼ÔǵÑÇâ¤Áä¿
Do not throw or drop any hard objects onto the top of fittings.
Í‹ÒãˌÇѵ¶Ø·Õè໚¹¢Í§á¢ç§Ëŋ¹ ËÃ×͵¡¡ÃÐá·¡ãʋºÃÔàdz˹ŒÒ¾×é¹¼ÔǢͧµÑÇâ¤Á
The surface temperature of the fitting can be very high after continuation in
service.
àÁ×èÍແ´ä¿·Ôé§änjã¹ÃÐÂÐàÇÅÒ˹Ö觨Ðà¡Ô´¤ÇÒÁÌ͹ÊÐÊÁºÃÔàdz´ŒÒ¹º¹¢Í§µÑÇâ¤Á俤ÇÃÃÐÁÑ´ÃÐÇѧ¡ÒÃ
ÊÑÁ¼Ñʶ١ºÃÔàdz´Ñ§¡Å‹ÒÇ
Proper use of this fitting must be observed.
¤ÇþԨÒóҤÇÒÁàËÁÒÐÊÁ¢Í§¾×é¹·Õè​ËÃ×͵íÒá˹‹§·Õè¨ÐµÔ´µÑ駵ÑÇâ¤Áä¿ µÑÇÍ‹ҧ ઋ¹ ÁÕ
¹éíҢѧ໚¹»ÃШíÒ㹺ÃÔàdz¹Ñé¹ËÃ×ÍäÁ‹? , Çѵ¶Øµ‹Ò§æ ઋ¹
´Ô¹,àÈÉãºäÁŒãºË­ŒÒÁÕâÍ¡ÒÈ·Õè¨ÐÁÒ»¡¤ÅØÁÊÐÊÁº¹Ë¹ŒÒâ¤Á໚¹»ÃÔÁÒ³ÁÒ¡ËÃ×ÍäÁ‹?
áÅÐäÁ‹¤ÇõԴµÑé§ã¹ºÃÔàdz·ÕèÍÒ¨ÁÕâÍ¡Òȶ١ÊÑÁ¼ÑÊâ´Â¤¹ â´Â੾ÒÐà´ç¡àÅç¡ËÃ×ÍÊѵǏàÅÕé§
YES/¶Ù¡µŒÍ§
Last Revised On : 25/09/2023 REV.01
NO/äÁ‹¶Ù¡µŒÍ§
4/6
NO/äÁ‹¶Ù¡µŒÍ§
FR-DM-17 REV.03 EFF 15/09/17
Walk over fittings. Max 500 Kg. constant pressure load.
â¤Ã§ÊÌҧ¢Í§â¤Á俪¹Ô´¹ÕéÊÒÁÒöà´Ô¹àËÂÕºº¹Ë¹Œ​Òâ¤Á䴌 áÅÐÃѺáç¡´·Ñºä´Œ 500 ¡¡.
For On-Off System
ÊíÒËÃѺ Ãкºà»´-»´
Cable Size/¢¹Ò´ÊÒÂä¿ : 2x1.00 mm.2 Ø4.8-6 mm.
In case the supply cable is exposed to sunlight use UV resistant cable.
¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃἋÃѧÊÕÂÙÇÕ ÊÒÂ俵ŒÍ§ÊÒÁÒö»‡Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òû‡Í§¡Ñ¹äÁ‹ãˌ¶¡Ù ÃѧÊÕÂÙÇÕ䴌
The luminaire should be positioned so that prolonged staring into the luminaire at
a distance closer than 0.5m in not expected.
µíÒá˹‹§·ÕèµÔ´µÑ駴ǧâ¤Á¤ÇÃÍÂً㹨ش·ÕèáʧäÁ‹Ê‹Í§à¢ŒÒ´Ç§µÒâ´ÂµÃ§à»š¹àÇÅÒ¹Ò¹ ËҡࢌÒã¡ÅŒã¹
ÃÐÂйŒÍÂ¡Ç‹Ò 0.5 Á.
Any damaged safety glass cover must be replaced only with the original
spare part.
àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËŋ᷌¨Ò¡¼ÙŒ¼ÅԵ෋ҹÑé¹
NO
Not using chemical compounds and aggressive agents such as , weed repellents
fertilizers , acid solvent and contaminated irrigation water near the Luminaires.
ˌÒÁ㪌ÊÒÃà¤ÁÕઋ¹ »Ø‰Â, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໚¹¡Ã´ áÅйéíÒ»¹à»„œÍ¹ÊÒÃà¤ÁÕ
ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿
Our products are installed with electronic components with the protection against
overvoltage according to IEC 61547. The customers have to install the additional
overvoltage protection devices (against surge, transients, etc) in their electrical
system to avoid the risk of damage. Failing to do so will end the product warranty.
¼ÅÔµÀѳ±¢Í§àÃÒÁÕ¡ÒõԴµÑé§ÍØ»¡Ã³ÍÔàÅç¡·Ã͹ԡʏÊíÒËÃѺ¡Òû‡Í§¡Ñ¹áç´Ñ¹ä¿à¡Ô¹µÒÁÁÒµÃฐÒ¹
IEC 61547 áÅÐÅÙ¡¤ŒÒµŒÍ§µÔ´µÑé§ÍØ»¡Ã³»Í‡ §¡Ñ¹áç´Ñ¹ä¿à¡Ô¹à¾ÔèÁàµÔÁ
(»‡Í§¡Ñ¹ä¿¡ÃЪҡ ,ä¿¿‡ÒÅѴǧ¨Ã ÏÅÏ) ã¹Ãкºä¿¿‡Ò´ŒÇ à¾×èÍËÅÕ¡àÅÕ觤ÇÒÁàÊÕ觷Õè¨Ðà¡Ô´¤ÇÒÁ
àÊÕÂËÒ ËÒ¡äÁ‹´íÒà¹Ô¹¡Òôѧ¡Å‹ÒÇ ¡ÒÃÃѺ»ÃСѹ¨ÐÊÔé¹Êشŧ
LED
NO
Last Revised On : 25/09/2023 REV.01
Clean the products regularly to maintain good light output and prolong surface
quality .
Only use solvent-free cleaning solutions on the products.
·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ±à»š¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁʋͧÊNjҧ·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ
㪌¹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁ‹ÁÕáÍÅ¡ÍÎÍŏËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·‹Ò¹Ñé¹
5/6
FR-DM-17 REV.03 EFF 15/09/17
NO
LED
LED
Do not use a high pressure washer to clean the products.
ˌÒÁ㪌à¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ±
To replace the LED module or the entrire luminaire.Please consult your
sales representative.
ËÒ¡µŒÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ×Íâ¤Áä¿â»Ã´µÔ´µ‹ÍµÑÇá·¹¢Ò¢ͧ¤Ø³
Environmental protection: Waste electrical products should not be disposed of
with household waste. please recycle where facilities exist.check with your local
authority or retailer for recycling advice According to directive 2002/96/CE and
directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE).
ˌÒÁ·Ô駼ÅÔµÀѳ±¹éÃÕ ‹ÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪌§Ò¹â»Ã´á¡¼ÅÔµÀѳ±ÍÍ¡
¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍ‹ҧàËÁÒÐÊÁà¾×èÍʋ§àÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪌«íÒé «Ö觨Ъ‹ÇÂ
»‡Í§¡Ñ¹ÍѹµÃÒµ‹ÍÊÔè§áǴŌÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹Øɏ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁ‹Á¡Õ ÒäǺ¤ØÁ
͌ҧÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and
Electronic Equipment (WEEE).
Replacing the LED module
ÇÔ¸Õ¡ÒÃà»ÅÕè¹ LED module
1. Contact your sales representative for replacement LED modules. Make sure that the replacement module
match the initially supplied module. Note the part number printed on the LED module.
àµÃÕÂÁ LED module ãˌµÃ§¡ÑºÃ؋¹·Õ赌ͧ¡ÒÃà»ÅÕè¹â´ÂµÃǨÊͺ·ÕèËÁÒÂàÅ¢·Õè¾ÔÁ¾º¹LED modules áÅÐ µÔ´µ‹ÍµÑÇá·¹¢ÒÂà¾×èÍÊÑ觫×éÍ
LED modules ·Õ赌ͧ¡ÒÃà»ÅÕè¹
2. The LED module can be replaced by qualified persons using standard tools.
¡ÒÃà»ÅÕè¹ LED module µŒÍ§·íÒâ´Âª‹Ò§¼ÙŒªíÒ¹Ò­áÅÐ㪌à¤Ã×èͧÁ×Í·Õè䴌ÁÒµÃฐÒ¹
3. Disconnect power before opening the luminaire housing.
µÑ´áËŋ§¨‹ÒÂä¿¡‹Í¹·Õè¨Ðແ´µÑÇâ¤Á
4. Replace the old LED module with the new LED module. Reapply thermal interface material as supplied with the
new LED module.
¶Í´ LED module ·ÕèªíÒÃØ´ÍÍ¡ ¨Ò¡¹ÑŒ¹·íÒ¤ÇÒÁÊÐÍÒ´¨Ø´ÇÒ§ËÅÍ´ áŌǨ֧·íÒ¡ÒûÃСͺ LED module ãËÁ‹ áÅеŒÍ§à»ÅÕè¹
Ἃ¹Thermal Pad ËÃ×Í Thermal Grease ´ŒÇ·ء¤ÃÑé§
5. Inspect gaskets and if required replace with new gaskets. Defective luminaire covers must be replaced. Inspect
correct wiring of replaced LED module.
µÃǨÊͺ»ÃÐà¡ç¹áÅЪÔé¹Ê‹Ç¹¢Í§µÑÇâ¤Á ¶ŒÒªíÒÃØ´àÊÕÂËÒÂãˌ·íÒ¡ÒÃà»ÅÕè¹ãËÁ‹ áÅеÃǨÊͺ¡ÒÃࢌÒÊÒÂ俢ͧ LED module
·Õèà»ÅÕè¹ãËÁ‹¶Ù¡µŒÍ§ËÃ×ÍäÁ‹
6. Close the luminaire housing before reconnecting power.
»´½Ò¤ÃͺÅçͤâ¤Áä¿ãˌàÃÕºÌÍ¡‹Í¹à»´ä¿
Last Revised On : 25/09/2023 REV.01
6/6
FR-DM-17 REV.03 EFF 15/09/17
">