INSTALLATION MANUAL PRODUCT NAME : VOLGA/1 - CV Ground / Concrete Wall Recess VOLGA/1 - CC Ground / Concrete Wall Recess No. Input lll IP68 Glass Temperature At Ta 50°C Ordering Code 1. Constant Voltage 24V 2. ( Output from SELV 3. system only) ( ¡ÃÐáÊ俵ͧÁÒ 4. ¨Ò¡Ãкºáç´Ñ¹ä¿¿Ò µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑ 5. à¾Õ§à·Ò¹Ñé¹) 6. 9007-4-2-361-91 65.5° C TA40° 9007-A-/6/C/H/U/0/2-429-91 61° C TA40° 9007-A-/6/C/H/U/0/2-2-430-91 61° C TA40° 9007-A-/6/C/H/U/0/2-2-431-91 61° C TA40° 9007-B/C/H/U/0-2-372-91 60° C TA25° 9007-B/C/H/U/0-2-373-91 60° C TA25° 7. 9007-B/C/H/U/0-2-374-91 60° C TA25° Current 8. Constant 700mA (CC) 9. Constant Current 1200mA (CC) 10. 9008-4-2-355-91 65.5° C TA40° 9008-A/6/C/H/U/0-2-561-91 60° C TA50° 9008-A/6/C/H/U/0-2-562-91 60° C TA50° 11. 9008-A/6/C/H/U/0-2-563-91 60° C TA50° - + 1-11 Light Emitting Diodes (LED) 1 2 108 û70 2.1 2.2 112 Cable length 200 mm. ÊÒÂä¿ÂÒÇ 200 ÁÁ. Please note the ground level. ¢Í¤ÇÃÃÐÇѧ : ¼ÔÇ˹ҢͧµÑÇâ¤Á¡Ñº¼ÔÇ ¾×鹤ÇÃÍÂÙã¹ÃйҺà´ÕÂǡѹ 95 Unit:mm. 2 Meters cable pre-wired from the factory. ÊÒÂä¿ÂÒÇ2àÁµÃ»ÃСͺÁÒ ¾ÃÍÁ¡ÑºµÑÇâ¤Á¨Ò¡âç§Ò¹ 105 150x150 50 concrete 20-30cm. Wire Mesh Cable conduit Ø22mm. 85 Gravel Approx size: 3 4 " Last Revised On : 25/09/2023 REV.01 1/6 FR-DM-17 REV.03 EFF 15/09/17 3 4 4 7 2 Cable size : 2x1.00 mm. 4.8-6mm. ¢¹Ò´ÊÒÂä¿ Gel-Filled IP68 Connector Cable Diameter 4.8 - 6mm. Available Separately à¨ÅµÍÊÒÂ信ѹ¹éíÒIP68,¢¹Ò´ÊÒÂä¿ Ø 4.8-6ÁÁ. ᡨíÒ˹ÒµҧËÒ¡ Ordering Code : AUN-CON-0024-00 'See connecting detail on manual.' ´ÙÃÒÂÅÐàÍÕ´·Õè¤ÙÁ×Í¡ÒõԴ Installation complete ¡ÒõԴµÑé§àÊÃç¨ÊÁºÙó Remote driver for 24V system. / For On-Off, DALI system. OD-9007 ä´ÃàÇÍõԴµÑ駹͡µÑÇâ¤ÁÊíÒËÃѺÃкºä¿ 24V / ÊíÒËÃѺÃкº à»´-»´ / DALI Luminaires 1-n Warning Please ensure that the led lamp is connected to the driver correctly. Wrong polarity connection cause a damage to the led lamp and driver. â»Ã´ÃÐÇѧ¡ÒõÍÊÒÂä¿ÊÅѺ¢ÑéÇ +ºÇ¡ -ź ¨Ò¡ä´ÃàÇÍÃÁÒà¢Ò·ÕèËÅÍ´ LED ËÒ¡µÍÊÅѺ¢ÑéÇ ¨Ð·íÒãËä´ÃàÇÍÃáÅÐËÅÍ´ LED à¡Ô´¤ÇÒÁàÊÕÂËÒ Input/à¢Ò 220-240 V~ L N AC + DC + 1 - + 2 - + n - - Output/ÍÍ¡ 24 V ( Output from SELV system only) (¡ÃÐáÊ俵ͧÁÒ¨Ò¡Ãкºáç´Ñ¹ä¿¿Ò µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂà¾Õ§à·Ò¹Ñé¹) Parallel wiring constant voltage Distance from luminaire to Driver ÃÐÂзҧ¨Ò¡µÑÇâ¤Á¶Ö§ ä´ÃàÇÍà Luminaire Wattage Maximum number of luminaires Conductor size / ¢¹Ò´ÊÒÂä¿ ¨íҹǹâ¤Á㹡ÒÃµÍ Accessory available separately./ÍØ»¡Ã³àÊÃÔÁ¨íÒ˹ÒÂᡵҧËÒ¡ Ordering Code Product Name 1.00 mm.2 1.50 mm.2 2.00 mm.2 AUN-DRG-0027-00 LED Constant Voltage Driver 24Vdc 72W. 3.3 W 1-7 luminaire 30 m 50 m 65 m AUN-DRG-0011-00 LED Constant Voltage Driver 24Vdc 150W. 3.3 W 1-11 luminaire 30 m 50 m 65 m AUN-DRG-0024-00 LED Constant Voltage Driver 24Vdc 200W. 3.3 W 1-13 luminaire 30 m 50 m 70 m Last Revised On : 25/09/2023 REV.01 2/6 FR-DM-17 REV.03 EFF 15/09/17 For Constant Current 700mA/1200mA (Remote driver) OD-9008 Warning Please ensure that the led lamp is connected to the driver correctly. Wrong polarity connection cause a damage to the led lamp and driver. â»Ã´ÃÐÇѧ¡ÒõÍÊÒÂä¿ÊÅѺ¢ÑéÇ +ºÇ¡ -ź ¨Ò¡ä´ÃàÇÍÃÁÒà¢Ò·ÕèËÅÍ´ LED ËÒ¡µÍÊÅѺ¢ÑéÇ ¨Ð·íÒãËä´ÃàÇÍÃáÅÐËÅÍ´ LED à¡Ô´¤ÇÒÁàÊÕÂËÒ L Input/à¢Ò 220-240 V~ N AC + - DC + 1 - Output/ÍÍ¡ 700mA/1200mA ( Output from SELV system only) (¡ÃÐáÊ俵ͧÁÒ¨Ò¡Ãкºáç´Ñ¹ä¿¿Ò µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂà¾Õ§à·Ò¹Ñé¹) Distance from luminaire to Driver ÃÐÂзҧ¨Ò¡µÑÇâ¤Á¶Ö§ ä´ÃàÇÍà Luminaire Wattage Maximum number of luminaires Conductor size / ¢¹Ò´ÊÒÂä¿ ¨íҹǹâ¤Á㹡ÒÃµÍ Accessory available separately./ÍØ»¡Ã³àÊÃÔÁ¨íÒ˹ÒÂᡵҧËÒ¡ Ordering Code Product Name AUN-GOP-0101-01 LED Constant Current Driver 700mA 4W. In IP67 GFR Polymer Box (On-Off). AUN-DRG-0012-00 LED Constant Current Driver 700mA 20W. In IP67 GFR Polymer Box (DALI) AUN-DRG-0007-00 LED Constant Current Driver 1200mA 6W. In IP67 GFR Polymer Box (On-Off). 1.00 mm.2 1.50 mm.2 2.00 mm.2 2.2 W 1 luminaire 55 m 85 m 110 m 2.2 W 1-3 luminaire 55 m 80 m 110 m 3.9 W 1 luminaire 10 m 15 m 20 m Remark : ËÁÒÂà赯 1. Installation should be carried out by a qualified electrician in accordance with appropriate national wiring regulation. ¡ÒõԴµÑé§â¤Áä¿¿ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´ÂªÒ§ä¿¿Ò ·ÕèÁÕ¤ÇÒÁÃÙáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿Ò â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿Ò 2. Disconnect the power before changing the lamp. »´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿ 3. For Class1 luminaire, the installation must be completed with earthing. ÊíÒËÃѺâ¤Áä¿·ÕèÁ¡Õ Òûͧ¡Ñ¹ä¿¿ÒÃÑèÇÃдѺ1 ¡ÒõԴµÑ駵ͧµÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑ´Ç 4. Do not exceed the maximum wattage. ËÒÁãªËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡ÇÒ·ÕèÃÐºØ ËÃ×ÍãªËÅÍ´¼Ô´»ÃÐàÀ· Warning : ¢Í¤ÇÃÃÐÇѧ 1. The manufacturer will not be liable or held responsible for any incorrect installation, misuse or improper use and unauthorised modification to the fittings. Failure to comply with mentioned warning may cause serious damage or serious injury to persons, animals or objects. If any modification is required please consult your dealer for the details. ·Ò§¼Ù¼ÅÔµäÁÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡ ¡ÒõԴµÑé§äÁ¶Ù¡ÇÔ¸Õ,㪧ҹ¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Á ã¹·Ø¡¡Ã³Õ«Öè§ ÊÔ觼Դ»¡µÔàËÅÒ¹Õ ÍÒ¨·íÒãËà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊÑµÇ ÊÔ觢ͧ ËÒ¡ÁÕ¢ÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµÍ§¡ÒûÃѺᵧµÑÇâ¤Á ãËàËÁÒÐÊÁ¡Ñº¡ÒÃ㪧ҹ¡ÃسҵԴµÍµÑÇá·¹¨íÒ˹ÒÂËÃ×ͼټÅÔµ 2. Where damage has occured to the fittings, please make the replacement with standard parts before use. 㹡óշèÁÕ Õªé¹Ô Êǹ»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡ÃسÒà»ÅÕè¹ ªÔé¹ÊǹãËÁ¡Í ¹¡ÒÃ㪧ҹ·Ø¡¤ÃÑé§ à¾×èͤÇÒÁ»ÅÍ´ÀÑ 5. Don't touch LED while maintaining or cleaning. ËÒÁÊÑÁ¼ÑÊËÅÍ´ LED ¢³ÐºíÒÃاÃÑ¡ÉÒ ËÃ×Í·íÒ¤ÇÒÁÊÐÍÒ´ Last Revised On : 25/09/2023 REV.01 3/6 FR-DM-17 REV.03 EFF 15/09/17 General installation guide ( highly recommended) ¢Íá¹Ð¹íÒ㹡ÒõԴµÑé§ Pic-1 ÃÙ»-1 200-300mm. Pic-2 ÃÙ»-2 Place the gravel 200-300 mm.depth underneath the casing for water drainage (Pic-1).Then do the testing by filling water into the casing and let it drain.The water should be drained out by 30 minutes. If not,the additional drainage pipe or other system must be applied (Pic-2) ¤ÇÃÇÒ§¡Í¹¡ÃǴ㵡Åͧ½§¾×é¹·ÕèÃÐÂÐÅÖ¡»ÃÐÁÒ³ 200-300 ÁÁ. à¾×èͪÇÂÃкÒ ¹éíÒ·Õè·ÇÁ¢Ñ§µÑÇâ¤Áä¿ ÊÒÁÒö·´Êͺ¡ÒÃÃкÒ¹éíÒâ´Âà·¹éíÒãÊ¡ÅͧãËàµçÁ ¹éíҨеͧÃкÒÂÍÍ¡ËÁ´ÀÒÂã¹àÇÅÒ 30¹Ò·Õ ËÒ¡äÁ໹µÒÁ¹Ñ鹤ÇÃÁÕ¡ÒÃµÍ ·ÍÃкÒ¹éíÒà¾ÔèÁàµÔÁ Cable conduit ·ÍÊÒÂä¿ Water drainage conduit. ·Í¹éíÒ·Ôé§ Installation should not be done under high humidity environment i.e. rainy day or after the rain,foggy weather....ect. äÁ¤ÇõԴµÑé§â¤Áä¿ã¹ªÇ§·ÕèÁÕ¤ÇÒÁª×é¹Ê٧હ Çѹ·Õè½¹µ¡µÅÍ´ËÃ×͵ԴµÑé§ËÅѧ ½¹ËÂØ´µ¡à¾ÃÒШзíÒãˤÇÒÁª×鹶١¢Ñ§äÇã¹µÑÇâ¤Áä¿ËÅѧ¨Ò¡¹Ñ鹨Ðà¡Ô´¡Òà ¤Çºá¹¹à»¹ÅÐÍͧËÃ×ÍË´¹éíÒà¡ÒеԴºÃÔàdz㵡ÃШ¡ÀÒÂã¹µÑÇâ¤Áä¿ Do not let the exposed part of the fittings be covered by the soil,dried weed or foliage as well as corrosive or aggressive substancechemicals. ÍÂÒ»ÅÍÂãËÁÕÊÔè§Ê¡»Ã¡àª¹ àÈÉ´Ô¹ ãºäÁ ËÃ×Í Ë­Òá˧ÃÇÁ¶Ö§à¤ÁÕ·Õè໹ÊÒÃ-¡Ñ´¡Ã͹ÁÒ»¡¤ÅØÁÊÐÊÁºÃÔàdz˹Ҿ×é¹¼ÔǵÑÇâ¤Áä¿ Do not throw or drop any hard objects onto the top of fittings. ÍÂÒãËÇѵ¶Ø·Õè໹¢Í§á¢ç§ËŹ ËÃ×͵¡¡ÃÐá·¡ãʺÃÔàdz˹Ҿ×é¹¼ÔǢͧµÑÇâ¤Á The surface temperature of the fitting can be very high after continuation in service. àÁ×èÍà»´ä¿·Ôé§äÇã¹ÃÐÂÐàÇÅÒ˹Ö觨Ðà¡Ô´¤ÇÒÁÃ͹ÊÐÊÁºÃÔàdz´Ò¹º¹¢Í§µÑÇâ¤Á俤ÇÃÃÐÁÑ´ÃÐÇѧ¡Òà ÊÑÁ¼Ñʶ١ºÃÔàdz´Ñ§¡ÅÒÇ Proper use of this fitting must be observed. ¤ÇþԨÒóҤÇÒÁàËÁÒÐÊÁ¢Í§¾×é¹·ÕèËÃ×͵íÒá˹§·Õè¨ÐµÔ´µÑ駵ÑÇâ¤Áä¿ µÑÇÍÂÒ§ હ ÁÕ ¹éíҢѧ໹»ÃШíÒ㹺ÃÔàdz¹Ñé¹ËÃ×ÍäÁ? , Çѵ¶ØµÒ§æ હ ´Ô¹,àÈÉãºäÁãºË­ÒÁÕâÍ¡ÒÈ·Õè¨ÐÁÒ»¡¤ÅØÁÊÐÊÁº¹Ë¹Òâ¤Á໹»ÃÔÁÒ³ÁÒ¡ËÃ×ÍäÁ? áÅÐäÁ¤ÇõԴµÑé§ã¹ºÃÔàdz·ÕèÍÒ¨ÁÕâÍ¡Òȶ١ÊÑÁ¼ÑÊâ´Â¤¹ â´Â੾ÒÐà´ç¡àÅç¡ËÃ×ÍÊѵÇàÅÕé§ YES/¶Ù¡µÍ§ Last Revised On : 25/09/2023 REV.01 NO/äÁ¶Ù¡µÍ§ 4/6 NO/äÁ¶Ù¡µÍ§ FR-DM-17 REV.03 EFF 15/09/17 Walk over fittings. Max 500 Kg. constant pressure load. â¤Ã§ÊÃÒ§¢Í§â¤Á俪¹Ô´¹ÕéÊÒÁÒöà´Ô¹àËÂÕºº¹Ë¹Òâ¤Áä´ áÅÐÃѺáç¡´·Ñºä´ 500 ¡¡. For On-Off System ÊíÒËÃѺ Ãкºà»´-»´ Cable Size/¢¹Ò´ÊÒÂä¿ : 2x1.00 mm.2 Ø4.8-6 mm. In case the supply cable is exposed to sunlight use UV resistant cable. ¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃá¼ÃѧÊÕÂÙÇÕ ÊÒÂ俵ͧÊÒÁÒö»Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òûͧ¡Ñ¹äÁã˶¡Ù ÃѧÊÕÂÙÇÕä´ The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 0.5m in not expected. µíÒá˹§·ÕèµÔ´µÑ駴ǧâ¤Á¤ÇÃÍÂÙ㹨ش·ÕèáʧäÁÊͧà¢Ò´Ç§µÒâ´ÂµÃ§à»¹àÇÅÒ¹Ò¹ ËÒ¡à¢Òã¡Åã¹ ÃÐÂйÍ¡ÇÒ 0.5 Á. Any damaged safety glass cover must be replaced only with the original spare part. àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËÅá·¨Ò¡¼Ù¼ÅÔµà·Ò¹Ñé¹ NO Not using chemical compounds and aggressive agents such as , weed repellents fertilizers , acid solvent and contaminated irrigation water near the Luminaires. ËÒÁãªÊÒÃà¤ÁÕહ »ØÂ, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໹¡Ã´ áÅйéíÒ»¹à»Í¹ÊÒÃà¤ÁÕ ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿ Our products are installed with electronic components with the protection against overvoltage according to IEC 61547. The customers have to install the additional overvoltage protection devices (against surge, transients, etc) in their electrical system to avoid the risk of damage. Failing to do so will end the product warranty. ¼ÅÔµÀѳ±¢Í§àÃÒÁÕ¡ÒõԴµÑé§ÍØ»¡Ã³ÍÔàÅç¡·Ã͹ԡÊÊíÒËÃѺ¡Òûͧ¡Ñ¹áç´Ñ¹ä¿à¡Ô¹µÒÁÁÒµÃฐÒ¹ IEC 61547 áÅÐÅÙ¡¤ÒµÍ§µÔ´µÑé§ÍØ»¡Ã³»Í §¡Ñ¹áç´Ñ¹ä¿à¡Ô¹à¾ÔèÁàµÔÁ (»Í§¡Ñ¹ä¿¡ÃЪҡ ,ä¿¿ÒÅѴǧ¨Ã ÏÅÏ) ã¹Ãкºä¿¿Ò´Ç à¾×èÍËÅÕ¡àÅÕ觤ÇÒÁàÊÕ觷Õè¨Ðà¡Ô´¤ÇÒÁ àÊÕÂËÒ ËÒ¡äÁ´íÒà¹Ô¹¡Òôѧ¡ÅÒÇ ¡ÒÃÃѺ»ÃСѹ¨ÐÊÔé¹Êشŧ LED NO Last Revised On : 25/09/2023 REV.01 Clean the products regularly to maintain good light output and prolong surface quality . Only use solvent-free cleaning solutions on the products. ·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ±à»¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁÊͧÊÇÒ§·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ ãª¹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁÁÕáÍÅ¡ÍÎÍÅËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·Ò¹Ñé¹ 5/6 FR-DM-17 REV.03 EFF 15/09/17 NO LED LED Do not use a high pressure washer to clean the products. ËÒÁãªà¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ± To replace the LED module or the entrire luminaire.Please consult your sales representative. ËÒ¡µÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ×Íâ¤Áä¿â»Ã´µÔ´µÍµÑÇá·¹¢Ò¢ͧ¤Ø³ Environmental protection: Waste electrical products should not be disposed of with household waste. please recycle where facilities exist.check with your local authority or retailer for recycling advice According to directive 2002/96/CE and directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE). ËÒÁ·Ô駼ÅÔµÀѳ±¹éÃÕ ÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪧ҹâ»Ã´á¡¼ÅÔµÀѳ±ÍÍ¡ ¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍÂÒ§àËÁÒÐÊÁà¾×èÍʧàÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪫íÒé «Ö觨ЪÇ »Í§¡Ñ¹ÍѹµÃÒµÍÊÔè§áÇ´ÅÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹ØÉ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁÁ¡Õ ÒäǺ¤ØÁ ÍÒ§ÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and Electronic Equipment (WEEE). Replacing the LED module ÇÔ¸Õ¡ÒÃà»ÅÕè¹ LED module 1. Contact your sales representative for replacement LED modules. Make sure that the replacement module match the initially supplied module. Note the part number printed on the LED module. àµÃÕÂÁ LED module ã˵ç¡ÑºÃع·ÕèµÍ§¡ÒÃà»ÅÕè¹â´ÂµÃǨÊͺ·ÕèËÁÒÂàÅ¢·Õè¾ÔÁ¾º¹LED modules áÅÐ µÔ´µÍµÑÇá·¹¢ÒÂà¾×èÍÊÑ觫×éÍ LED modules ·ÕèµÍ§¡ÒÃà»ÅÕè¹ 2. The LED module can be replaced by qualified persons using standard tools. ¡ÒÃà»ÅÕè¹ LED module µÍ§·íÒâ´ÂªÒ§¼ÙªíÒ¹Ò­áÅÐãªà¤Ã×èͧÁ×Í·Õèä´ÁÒµÃฐÒ¹ 3. Disconnect power before opening the luminaire housing. µÑ´áËŧ¨ÒÂ信͹·Õè¨Ðà»´µÑÇâ¤Á 4. Replace the old LED module with the new LED module. Reapply thermal interface material as supplied with the new LED module. ¶Í´ LED module ·ÕèªíÒÃØ´ÍÍ¡ ¨Ò¡¹Ñ¹·íÒ¤ÇÒÁÊÐÍÒ´¨Ø´ÇÒ§ËÅÍ´ áÅǨ֧·íÒ¡ÒûÃСͺ LED module ãËÁ áÅеͧà»ÅÕè¹ á¼¹Thermal Pad ËÃ×Í Thermal Grease ´Ç·ء¤ÃÑé§ 5. Inspect gaskets and if required replace with new gaskets. Defective luminaire covers must be replaced. Inspect correct wiring of replaced LED module. µÃǨÊͺ»ÃÐà¡ç¹áÅЪÔé¹Êǹ¢Í§µÑÇâ¤Á ¶ÒªíÒÃØ´àÊÕÂËÒÂãË·íÒ¡ÒÃà»ÅÕè¹ãËÁ áÅеÃǨÊͺ¡ÒÃà¢ÒÊÒÂ俢ͧ LED module ·Õèà»ÅÕè¹ãËÁ¶Ù¡µÍ§ËÃ×ÍäÁ 6. Close the luminaire housing before reconnecting power. »´½Ò¤ÃͺÅçͤâ¤Áä¿ãËàÃÕºÃÍÂ¡Í¹à»´ä¿ Last Revised On : 25/09/2023 REV.01 6/6 FR-DM-17 REV.03 EFF 15/09/17 ">
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato.
