Motorline SLIDE800A-OL1500-OL2000 Manuel du propriétaire

PDF
Document
MOTORLINE SLIDE & OL : Notice avec IA + PDF | Fixfr
/

User questions

Y Z

Robert Y.

What are the electrical wiring color codes and installation requirements for the electronic control unit of gate motor models 800A, OL1500, and OL2000?

No votes

For gate motor models 800A and OL1500, the wiring color codes are: Yellow/Green for ground, Brown for MOTOR-AB, Blue for MOTOR-COM, and Black for MOTOR-FE. The OL2000 model requires a specific configuration with two capacitors. The electronic control unit must be installed in a location protected from liquids, moisture, and dust, with all cables entering the junction boxes from the bottom.

B A

Jennifer B.

How to adjust the clutch, rack, and limit switches of a gate motor?

No votes

To adjust the motor force (clutch), use a 6 mm hex key on the adjustment screw at the top of the motor: turn clockwise (+) to increase the motor's power or counter-clockwise (-) if the motor does not move correctly at idle. For the rack, adjust its position using the oval holes in the mounting screws to eliminate friction with the pinion. Set the limit switch plates so the gate stops before reaching the mechanical stops.

Y Z

Robert Y.

What are the installation requirements for the electronic control unit?

No votes

The electronic control unit must be installed in a place protected from liquids, humidity, and dust. All cables must enter the junction and control boxes from below.

B A

Jennifer B.

How to adjust the clutch of a motorized gate?

No votes

To adjust the motor's force, access the adjustment screw located in the upper part of the motor (using a 6 mm hex key). Turn clockwise (+) to increase irreversibility if the gate moves manually, or in the opposite direction (-) if the motor does not move correctly at slow speed.

B A

Jennifer B.

How to adjust the rack of a motorized gate?

No votes

If rubbing occurs between the pinion and the rack, adjust the rack's position using the elongated holes of the fixing screws.

B A

Jennifer B.

How to adjust the limit switches of a motorized gate?

No votes

The limit switch plates must be adjusted so that the gate stops before reaching the mechanical stops.

Y Z

Robert Y.

What are the wiring color codes for the motor connections of models 800A and OL1500?

No votes

For models 800A and OL1500, the wiring colors are: Yellow/Green for Earth, Brown for MOTOR-AB, Blue for MOTOR-COM, and Black for MOTOR-FE. The electronic control unit must be installed in an area protected from liquids, moisture, and dust, with all cables entering the boxes from below.

B A

Jennifer B.

How to adjust the motor clutch, rack, and limit switches of a motorized gate?

No votes

Adjust the motor clutch using a 6mm hex key on the top screw (turn clockwise to increase force). For the rack, use the oval mounting holes to adjust its position and avoid friction with the pinion. Set the limit switch plates so the gate stops before reaching its mechanical buffers.

Y Z

Robert Y.

How to connect the electronics for various motor models?

No votes

For models 800A and OL1500, connect wires according to the color code: Yellow/Green for ground, Brown for MOTOR-AB, Blue for MOTOR-COM, and Black for MOTOR-FE. The OL2000 model requires two capacitors. The electronic unit must be installed in a location protected from moisture and dust, with all cables entering the boxes from below.

B A

Jennifer B.

How to adjust a motorized gate system?

No votes

To adjust the motor force (clutch), use a 6 mm hex key on the adjustment screw: turn clockwise to increase power or counter-clockwise if the motor movement is insufficient. The rack can be adjusted via the oval mounting holes to reduce friction, and limit switches should be set to stop the gate before it hits mechanical buffers.

Y Z

Robert Y.

How are the electronic connections wired for the 800A, OL1500, and OL2000 models?

No votes

For models 800A and OL1500, the wiring follows these color codes: Yellow/Green for ground, Brown for MOTOR-AB, Blue for MOTOR-COM, and Black for MOTOR-FE. The OL2000 model requires a specific configuration with two capacitors. All cabling must enter the junction boxes from the bottom to protect against moisture and dust.

Preparing document for printing…
0%