Genesis ® G4 pour 1/4" & 3/16" Avdelok ®
Instructions de montage pour les ensembles de nez Genesis® nG4/G4/G4HD 3/16 & 1/4 Avdelok®
IMPORTANT
VEILLER A DECONNECTER L’ALIMENTATION EN AIR AVANT LA DEPOSE DE L’EQUIPEMENT
Les pièces suivantes NE SONT PAS requises et doivent être déposées de l’outil de base avant de commencer le montage de l’équipement de
nez Avdelok®. Les numéros de pièce peuvent être identifiés en se référant au schéma d’assemblage de l’outil dans le manuel de l’outil approprié.
71210-02101 Carter guide
71230-02102 Manchon de vide
71230-02015 Ecrou de blocage
71210-02104 Logement de joint
Montage de l’ensemble de nez Avdelok (Se reporter aux numéros de repère ( ) indiqués dans le tableau ci-dessous)
®
11) entièrement sur le piston.
1. Visser l’écrou de blocage (1
9) entièrement sur le piston avant de serrer l’écrou de blocage contre ce dernier. Poser la rondelle de frottement (1
10).
2. Visser l’adaptateur (9
6), le guide de ressort (7
7) et le ressort (8
8) dans le boîtier de mors (5
5). Enduire légèrement les
3. Assembler les mâchoires de mors (6
mâchoires et l’alésage interne du boîtier de mors avec de la graisse au bisulfure de molybdène.
9) et serrer.
4. Visser l’ensemble de boîtier de mors sur l’adaptateur (9
3) sur le boîtier de mors et visser l’ensemble de tête.
5. Poser l’enclume (3
2) et le carter d’enclume (1
1) sur l’enclume et maintenir en place à l’aide de l’enveloppe de protection en caoutchouc (4
4).
6. Assembler le butoir (2
Remarque : Enduire de savon la surface interne de l’enveloppe de protection en caoutchouc pour en faciliter la pose.
1/4 AVDELOK® ENSEMBLE DE NEZ 71230-05020
REPERE
71230-05020 pour l’équipement 6,4 (1/4") Avdelok®
3/16 AVDELOK® ENSEMBLE DE NEZ 71230-05010
REPERE
71230-05010 pour l’équipement 4,8 (3/16") Avdelok®
1
71230-05012
Carter d’enclume
1
71230-05012
Carter d’enclume
2
71230-05014
Butoir
2
71230-05014
Butoir
3
71230-05021
Enclume
3
71230-05011
Enclume
4
71230-05013
Enveloppe de protection en caoutchouc
4
71230-05013
Enveloppe de protection en caoutchouc
5
07200-02201
Boîtier de mors
5
07200-02101
Boîtier de mors
6
07220-02302
Mâchoires de mors
6
07220-02102
Mâchoires de mors
7
07220-02104
Guide de ressort
7
07220-02104
Guide de ressort
8
07220-02103
Ressort
8
07220-02103
Ressort
9
07610-00501
Adaptateur de boîtier de mors
9
07610-00501
Adaptateur de boîtier de mors
10
07610-02004
Rondelle de frottement
10
07610-02004
Rondelle de frottement
11
71233-20200
Ecrou de blocage
11
71233-20200
Ecrou de blocage
Since 1 936
2010
ALLEMAGNE
Avdel Deutschland GmbH
Klusriede 24
30851 Langenhagen
Tel:
+49 (0) 511 7288 0
Fax: +49 (0) 511 7288 133
AvdelDeutschland@infastech.com
CORRÉ DU SUD
Infastech (Korea) Ltd.
212-4, Suyang-Ri,
Silchon-Eup, Kwangju-City,
Kyunggi-Do, Korea, 464-874
Tel:
+82 31 798 6340
Fax: +82 31 798 6342
info@infastech.co.kr
AUSTRALIE
Infastech (Australia) Pty Ltd.
891 Wellington Road
Rowville
Victoria 3178
Tel:
+61 3 9765 6400
Fax: +61 3 9765 6445
info@infastech.com.au
ESPAGNE
Avdel Spain S.A.
C/ Puerto de la Morcuera, 14
Poligono Industrial Prado Overa
Ctra. de Toledo, km 7,8
28919 Leganés (Madrid)
Tel:
+34 91 3416767
Fax: +34 91 3416740
ventas@infastech.com
CANADA
Avdel Canada Limited
1030 Lorimar Drive
Mississauga
Ontario L5S 1R8
Tel:
+1 905 364 0664
Fax: +1 905 364 0678
infoAvdel-Canada@infastech.com
FRANCE
Avdel France S.A.S.
33 bis, rue des Ardennes
BP4
75921 Paris Cedex 19
Tel:
+33 (0) 1 4040 8000
Fax: +33 (0) 1 4208 2450
AvdelFrance@infastech.com
CHINE
Infastech (China) Ltd.
RM 1708, 17/F., Nanyang Plaza,
57 Hung To Rd., Kwun Tong
Hong Kong
Tel:
+852 2950 0631
Fax: +852 2950 0022
infochina@infastech.com
Feuille de données
techniques n°
07900-00795
INDE
Infastech Fastening Technologies
India Private Limited
Plot No OZ-14, Hi Tech SEZ,
SIPCOT Industrial Growth Center,
Oragadam, Sriperumbudur Taluk,
Kanchipuram District,
602105 Tamilnadu
Tel:
+91 44 4711 8001
Fax: +91 44 4711 8009
info-in@infastech.com
Edition
ITALIE
Avdel Italia S.r.l.
Viale Lombardia 51/53
20047 Brugherio (MI)
Tel:
+39 039 289911
Fax: +39 039 2873079
vendite@infastech.com
JAPON
Infastech Kabushiki Kaisha
Center Minami SKY,
3-1 Chigasaki-Chuo, Tsuzuki-ku,
Yokohama-city,
Kanagawa Prefecture
Japan 224-0032
Tel:
+81 45 947 1200
Fax: +81 45 947 1205
info@infastech.co.jp
MALAISIE
Infastech (Malaysia) Sdn Bhd
Lot 63, Persiaran Bunga Tanjung 1,
Senawang Industrial Park
70400 Seremban
Negeri Sembilan
+606 676 7168
Tel:
Fax: +606 676 7101
info-my@infastech.com
SINGAPOUR
Infastech (Singapore) Pte Ltd.
31 Kaki Bukit Road 3
#05-03/06 Techlink
Singapore, 417818
Tel:
+65 6372 5653
Fax: +65 6744 5643
info-sg@infastech.com
TAÏWAN
Infastech/Tri-Star Limited
No 269-7, Baodong Rd,
Guanmiao Township,
71841 Tainan County,
Taiwan, R.O.C
+886 6 596 5798 (ext 201)
Tel:
Fax: +886 6 596 5758
info-tw@infastech.com
USA
Avdel USA LLC
614 NC Highway 200 South
Stanfield, North Carolina 28163
Tel:
+1 704 888 7100
Fax: +1 704 888 0258
infoAvdel-USA@infastech.com
ROYAUME-UNI
Avdel UK Limited
Pacific House
2 Swiftfields
Watchmead Industrial Estate
Welwyn Garden City
Hertfordshire AL7 1LY
Tel:
+44 (0) 1707 292000
Fax: +44 (0) 1707 292199
enquiries@infastech.com
N° de modification
B
07/288
B2
11/018
www.avdel-global.com
www.infastech.com
Autosert® (equipment), Avbolt ®, Avdel®, Avdelmate ®, Avdel TX2000®, Avdelok®, Avex®, Avibulb ®, Avinox®, Avinut™, Avlug®, Avmatic®, Avplas®,
Avseal ®, Avsert®, Avtainer ®, Avtronic®, Briv®, Bulbex®, Chobert®, Eurosert®, Fastriv®, Finsert®, Genesis®, Grovit®, Hemlok®, Hexsert®, Holding
your world together®, Hydra®, Interlock®, Klamp-Tite ®, Klamptite KTR ®, Kvex®, Maxlok ®, Monobolt ®, Monobulb ®, Neobolt®, Nutsert®, Nutsert
SQ®, Portariv®, Rivmatic ®, Rivscrew®, Speed Fastening®, Squaresert®, Stavex®, Supersert®, Thin Sheet Nutsert ®, Titan®, T-Lok®, TLR®,
TSN®, TX2000®, Versa-Nut ®, Viking® et Viking 360 ® sont des marques déposées de Avdel UK Limited. Infastech™ et Our Technology, Your
Success™ sont des marques déposées de Infastech Intellectual Properties Pte Ltd. Les noms et logos d’autres sociétés mentionnées
peuvent être des marques de leur propres sociétés. Ce document est purement informatif. Infastech ne donne aucune garantie, expresse
ou implicite dans ce document. La société se réserve la possibilité de modifier à tout moment les données figurant sur le présent document
dans le cadre de sa procédure de développement et d’amélioration continue des produits. Votre représentant Avdel est à votre disposition,
si vous avez besoin de valider les dernières données techniques mises en oeuvre.
02.2011 • © 2010 Infastech
Since 1922
Genesis ® G4 for 1/4"& 3/16" Avdelok ®
Fitting Instructions for Genesis ® nG4/G4/G4HD 3/16 & 1/4 Avdelok ® Nose Assemblies
IMPORTANT
THE AIR SUPPLY MUST ALWAYS BE DISCONNECTED BEFORE ANY DISMANTLING IS ATTEMPTED
The following parts are NOT required and must be removed from the basic tool before assembly of the Avdelok® nose equipment can
commence. Part numbers can be identified by referring to the tool assembly diagram in the appropriate tool manual.
71210-02101 Jaw Spreader Housing
71230-02102 Vacumm Sleeve
71230-02015 Locknut
71210-02104 Seal Housing
®
Assembly of Avdelok Nose Assembly (Refer to Item Numbers ( ) listed in the table below)
1. Screw Locknut (11) fully onto the piston.
2. Screw Adaptor (9) fully onto the piston before tightening the locknut against it. Fit Friction Ring (10).
3. Assemble Chuck jaws (6), Spring Guide (7) and Spring (8) into the Chuck Collet (5). Lightly coat the Jaws and the internal bore of the
Chuck Collet with Molylithium grease.
4. Screw the Chuck Collet assembly onto the Adaptor (9) and tighten.
5. Assemble the Anvil (3) over the Chuck Collet and screw into the head Assembly.
6. Assemble the Buffer (2) and the Anvil Casing (1) over the Anvil and retain in place with the Rubber Shroud (4).
Note: For ease of fitting the Rubber Shroud, smear liquid soap on its internal surface.
1/4 AVDELOK® NOSE ASSEMBLY 71230-05020
ITEM
1
2
3
4
5
6
7
8
9
10
11
71230-05020 for 6.4 (1/4") Avdelok®
71230-05012
71230-05014
71230-05021
71230-05013
07200-02201
07220-02302
07220-02104
07220-02103
07610-00501
07610-02004
71233-20200
Anvil Casing
Buffer
Anvil
Rubber Shroud
Chuck Collet
Chuck Jaws
Spring Guide
Spring
Chuck Collet Adapter
Friction Ring
Locknut
3/16 AVDELOK® NOSE ASSEMBLY 71230-05010
ITEM
1
2
3
4
5
6
7
8
9
10
11
71230-05010 for 4.8 (3/16") Avdelok®
71230-05012
71230-05014
71230-05011
71230-05013
07200-02101
07220-02102
07220-02104
07220-02103
07610-00501
07610-02004
71233-20200
Anvil Casing
Buffer
Anvil
Rubber Shroud
Chuck Collet
Chuck Jaws
Spring Guide
Spring
Chuck Collet Adapter
Friction Ring
Locknut
Since 1 936
2010
AUSTRALIA
Infastech (Australia) Pty Ltd.
891 Wellington Road
Rowville
Victoria 3178
Tel:
+61 3 9765 6400
Fax: +61 3 9765 6445
info@infastech.com.au
GERMANY
Avdel Deutschland GmbH
Klusriede 24
30851 Langenhagen
Tel:
+49 (0) 511 7288 0
Fax: +49 (0) 511 7288 133
AvdelDeutschland@infastech.com
INDIA
Infastech Fastening Technologies
India Private Limited
Plot No OZ-14, Hi Tech SEZ,
SIPCOT Industrial Growth Center,
Oragadam, Sriperumbudur Taluk,
Kanchipuram District,
602105 Tamilnadu
Tel:
+91 44 4711 8001
Fax: +91 44 4711 8009
info-in@infastech.com
CANADA
Avdel Canada Limited
1030 Lorimar Drive
Mississauga
Ontario L5S 1R8
Tel:
+1 905 364 0664
Fax: +1 905 364 0678
infoAvdel-Canada@infastech.com
CHINA
Infastech (China) Ltd.
RM 1708, 17/F., Nanyang Plaza,
57 Hung To Rd., Kwun Tong
Hong Kong
Tel:
+852 2950 0631
Fax: +852 2950 0022
infochina@infastech.com
ITALY
Avdel Italia S.r.l.
Viale Lombardia 51/53
20047 Brugherio (MI)
Tel:
+39 039 289911
Fax: +39 039 2873079
vendite@infastech.com
FRANCE
Avdel France S.A.S.
33 bis, rue des Ardennes
BP4
75921 Paris Cedex 19
Tel:
+33 (0) 1 4040 8000
Fax: +33 (0) 1 4208 2450
AvdelFrance@infastech.com
Data Sheet No.
07900-00795
JAPAN
Infastech Kabushiki Kaisha
Center Minami SKY,
3-1 Chigasaki-Chuo, Tsuzuki-ku,
Yokohama-city,
Kanagawa Prefecture
Japan 224-0032
Tel:
+81 45 947 1200
Fax: +81 45 947 1205
info@infastech.co.jp
Issue
MALAYSIA
Infastech (Malaysia) Sdn Bhd
Lot 63, Persiaran Bunga Tanjung 1,
Senawang Industrial Park
70400 Seremban
Negeri Sembilan
+606 676 7168
Tel:
Fax: +606 676 7101
info-my@infastech.com
TAIWAN
Infastech/Tri-Star Limited
No 269-7, Baodong Rd,
Guanmiao Township,
71841 Tainan County,
Taiwan, R.O.C
+886 6 596 5798 (ext 201)
Tel:
Fax: +886 6 596 5758
info-tw@infastech.com
SINGAPORE
Infastech (Singapore) Pte Ltd.
31 Kaki Bukit Road 3
#05-03/06 Techlink
Singapore, 417818
Tel:
+65 6372 5653
Fax: +65 6744 5643
info-sg@infastech.com
UNITED KINGDOM
Avdel UK Limited
Pacific House
2 Swiftfields
Watchmead Industrial Estate
Welwyn Garden City
Hertfordshire AL7 1LY
Tel:
+44 (0) 1707 292000
Fax: +44 (0) 1707 292199
enquiries@infastech.com
SOUTH KOREA
Infastech (Korea) Ltd.
212-4, Suyang-Ri,
Silchon-Eup, Kwangju-City,
Kyunggi-Do, Korea, 464-874
Tel:
+82 31 798 6340
Fax: +82 31 798 6342
info@infastech.co.kr
USA
Avdel USA LLC
614 NC Highway 200 South
Stanfield, North Carolina 28163
Tel:
+1 704 888 7100
Fax: +1 704 888 0258
infoAvdel-USA@infastech.com
SPAIN
Avdel Spain S.A.
C/ Puerto de la Morcuera, 14
Poligono Industrial Prado Overa
Ctra. de Toledo, km 7,8
28919 Leganés (Madrid)
Tel:
+34 91 3416767
Fax: +34 91 3416740
ventas@infastech.com
Change Note No.
B
07/288
B2
11/018
www.avdel-global.com
www.infastech.com
Autosert® (equipment), Avbolt ®, Avdel®, Avdelmate ®, Avdel TX2000®, Avdelok®, Avex®, Avibulb ®, Avinox®, Avinut™, Avlug®, Avmatic®, Avplas®,
Avseal ®, Avsert®, Avtainer ®, Avtronic®, Briv®, Bulbex®, Chobert®, Eurosert®, Fastriv®, Finsert®, Genesis®, Grovit®, Hemlok®, Hexsert®, Holding
your world together®, Hydra®, Interlock®, Klamp-Tite ®, Klamptite KTR ®, Kvex®, Maxlok ®, Monobolt ®, Monobulb ®, Neobolt®, Nutsert®, Nutsert
SQ®, Portariv®, Rivmatic ®, Rivscrew®, Speed Fastening®, Squaresert®, Stavex®, Supersert®, Thin Sheet Nutsert ®, Titan®, T-Lok®, TLR®, TSN®,
TX2000®, Versa-Nut ®, Viking® and Viking 360 ® are trademarks of Avdel UK Limited. Infastech™ and Our Technology, Your Success™ are
trademarks of Infastech Intellectual Properties Pte Ltd. The names and logos of other companies mentioned herein may be trademarks
of their respective owners. This document is for informational purposes only. Infastech makes no warranties, expressed or implied, in this
document. Data shown is subject to change without prior notice as a result of continuous product development and improvement policy.
Your local Avdel representative is at your disposal should you need to confirm latest information.
02.2011 • © 2010 Infastech
Since 1922
">
