Allen-Bradley 140G Flange Cable Guide d'installation

Bul. 140G/140MG
140G-G-EZ, 140G-J-EZ
Installation instruction for Flange Cable Operator Mounting Plate for 140G-G through K
Istruzioni di installazione
Installationsanleitung
Instructions pour l’installation
Instrucciones de instalación
Installation - Installazione - Instalación
Instalação WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
Tools
Needed:
CLACK
140G-J-EZ
140G-G-EZ
xx lb-in
xx N-m
T25 TORX
M5 x 12 mm
Thread Forming
3X
xx lb-in
xx N-m
#2 Phillips
PN-498045
DIR 10003963284 (Version 00)
M5 x 12 mm
Thread Forming
4X
140G-G-EZ Shown
1 Drill Holes.
140G-G-EZ
140G-J-EZ
G/H
I/J/K
1.07 in
(27 mm)
3.15 in
(80 mm)
7.60 in
(193 mm)
9.25 in
(235 mm)
2.13 in
(54 mm)
Ø.177 in
(4.5 mm)
PN-498045
DIR 10003963284 (Version 00)
Ø.177 in
(4.5 mm)
(2)
2
Insert screws partially.
140G-G-EZ Shown
10 lb-in
(1.2 N-m)
3 Mounting Option 1:
Place mounting plate openings over screws.
140G-G-EZ Shown
2
1
PN-498045
DIR 10003963284 (Version 00)
(3)
4
Tighten screws.
140G-G-EZ Shown
30 lb-in
(3.4 N-m)
5 Mounting Option 2:
Correct Assembly
Orientation
Assemble MCCB to Bail and Mounting Plate.
140G-G-EZ Shown
ON
OFF
7-11 lb-in
(0.8-1.2 N-m)
ON
OFF
#2 PHILLIPS
PN-498045
DIR 10003963284 (Version 00)
(4)
6
Place mounting plate openings over screws.
140G-G-EZ Shown
7 Tighten screws.
140G-G-EZ Shown
30 lb-in
(3.4 N-m)
PN-498045
DIR 10003963284 (Version 00)
(5)
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Product certificates are located in the Rockwell Automation Literature Library: http://www.rockwellautomation.com/global/literature-library/overview.page. Publication No.: 140G-CT009.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN158A-MU-P - June 2018
PN-498045
DIR 10003963284 (Version 00)
Copyright © 2018 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
">