Unilamp ZET Round Opal Mode d'emploi

INSTALLATION MANUAL
PRODUCT NAME : ZET1 - Frost, ZET2 - Frost,
: ZET1 - Clear, ZET2 - Clear
*
***
lll
IP67
Ordering Code
Glass Temperature
At Ta 25°C
1. 230V~50Hz MAX QPAR51 50W
9002/9004/9011/9021-0-2-221-91 *
170.1° C
2. 12V~50W QR-CB51 50W
9002/9004/9011/9021-0-2-281-91 ***
138.6° C
Applicable lamp
No.
1
2
1
2
Tungsten Halogen
GU10
Tungsten Halogen
GU5.3
130
2.1
û129
173
173
130
2.3
û108
û108
ZET1 - Frost/ZET1 - Clear
ZET2 - Frost/ZET2 - Clear
3
2.2
For class I
2.4
Please note the ground level.
¢ŒÍ¤ÇÃÃÐÇѧ : ¼ÔÇ˹ŒÒ¢Í§µÑÇâ¤Á¡Ñº¼ÔǾ×é¹
¤ÇÃÍÂًã¹ÃйҺà´ÕÂǡѹ
6
25
6
30
Cable size : 3x1.00 mm.2 Ø8-10mm.
¢¹Ò´ÊÒÂä¿
Last Revised On : 26/03/2024 REV.10
Ø122
170
1/5
FR-DD-29 REV.00 EFF11/03/24
3
4
For class III lll
Please prepare the space for installation.
¤ÇÃàµÃÕÂÁ¾×é¹·Õèà¼×èÍÊíÒËÃѺ¡ÒõԴµÑé§änj´ŒÇÂ
Please note the ground level.
¢ŒÍ¤ÇÃÃÐÇѧ:¼ÔÇ˹ŒÒ¢Í§µÑÇâ¤Á¡Ñº¼ÔǾ×é¹
¤ÇÃÍÂًã¹ÃйҺà´ÕÂǡѹ
Output/ÍÍ¡
Transformer box
available separately.
¡Å‹Í§ËÁŒÍá»Å§á¡¨íÒ˹‹ÒÂ
SEC
Input
ࢌÒ
PRI
Out
ÍÍ¡
SEC
Input/ࢌÒ
25
Ø122
PRI
6
170
Cable size : 2x1.00 mm.2 Ø6-13mm.
¢¹Ò´ÊÒÂä¿
Distance from the luminaire to transformer /
Driver should not exceed 10 meters.
ÃÐÂÐˋҧÃÐËNjҧµÑÇâ¤Á¶Ö§ËÁŒÍá»Å§ËÃ×Íä´ÃàÇÍÏäÁ‹¤ÇÃà¡Ô¹ 10 àÁµÃ
5
6
6.1
5.2
6.2
6.3
5.3
5.1
7
8
7.7
7.6
1
8.2
7.4
7.2
7.5
8.1
7.1
2
Lock the screws following
this sequence.
¤ÇâѹʡÃÙµÒÁÅíҴѺ¢Í§ËÁÒÂ
àÅ¢·ÕèÃкØänjµÒÁÃÙ»ÀÒ¾
Torque/áçºÔ´ : 1.0 Nm.
7.3
Last Revised On : 26/03/2024 REV.10
3
4
8.3
2/5
FR-DD-29 REV.00 EFF11/03/24
9
9.4
9.3
Torque/áçºÔ´ : 1.0 Nm.
10
9.2
9.1
Torque/áçºÔ´ : 1.0 Nm.
Installation complete
¡ÒõԴµÑé§àÊÃç¨ÊÁºÙó
Remark :
ËÁÒÂà˵Ø
Warning :
¢ŒÍ¤ÇÃÃÐÇѧ
1. The manufacturer will not be liable or held responsible
for any incorrect installation, misuse or improper use
and unauthorised modification to the fittings. Failure
to comply with mentioned warning may cause serious
damage or serious injury to persons, animals or
objects. If any modification is required please consult
your dealer for the details.
·Ò§¼ÙŒ¼ÅÔµäÁ‹ÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡¡ÒÃ
µÔ´µÑé§äÁ‹¶¡Ù ÇÔ¸Õ, 㪌§Ò¹¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Áã¹·Ø¡¡Ã³Õ
«Öè§ ÊÔ觼Դ»¡µÔàËŋҹÕé ÍÒ¨·íÒãˌà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊѵǏ ÊÔ觢ͧ
ËÒ¡ÁÕ¢ŒÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµŒÍ§¡ÒûÃѺᵋ§µÑÇâ¤Á
ãˌàËÁÒÐÊÁ¡Ñº¡ÒÃ㪌§Ò¹ ¡ÃسҵԴµ‹ÍµÑÇá·¹¨íÒ˹‹ÒÂËÃ×ͼٌ¼ÅÔµ
1. Installation should be carried out by a qualified
electrician in accordance with appropriate national
wiring regulation.
¡ÒõԴµÑé§â¤Áä¿¿‡ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´Âª‹Ò§ä¿¿‡Ò
·ÕèÁÕ¤ÇÒÁÃٌáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿‡Ò
â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿‡Ò
2. Disconnect the power before changing the lamp.
»´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿
3. For Class1 luminaire, the installation must be
completed with earthing.
ÊíÒËÃѺâ¤Áä¿·ÕèÁ¡Õ Òû‡Í§¡Ñ¹ä¿¿‡ÒÃÑèÇÃдѺ1
¡ÒõԴµÑ駵ŒÍ§µ‹ÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑ´ŒÇÂ
2. Where damage has occured to the fittings, please
make the replacement with standard parts before use.
㹡óշèÁÕ ÕªÔé¹Ê‹Ç¹»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡ÃسÒà»ÅÕ蹪Թé
ʋǹãËÁ‹¡‹Í¹¡ÒÃ㪌§Ò¹·Ø¡¤ÃÑé§ à¾×èͤÇÒÁ»ÅÍ´ÀÑÂ
4. Do not exceed the maximum wattage.
ˌÒÁ㪌ËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡Ç‹Ò·ÕèÃÐºØ ËÃ×Í㪌ËÅÍ´¼Ô´»ÃÐàÀ·
For class I
Cable Size/¢¹Ò´ÊÒÂä¿ : 3x1.00 mm.2 Ø6-13 mm.
For class III lll
Cable Size/¢¹Ò´ÊÒÂä¿ : 2x1.00 mm.2 Ø6-13 mm.
In case the supply cable is exposed to sunlight use UV resistant cable.
¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃἋÃѧÊÕÂÙÇÕ ÊÒÂ俵ŒÍ§ÊÒÁÒö»‡Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òû‡Í§¡Ñ¹äÁ‹ãˌ¶¡Ù ÃѧÊÕÂÙÇÕ䴌
Last Revised On : 26/03/2024 REV.10
3/5
FR-DD-29 REV.00 EFF11/03/24
General installation guide (highly recommended)
¢ŒÍá¹Ð¹íÒ㹡ÒõԴµÑé§
Pic-1
ÃÙ»-1
20-30 cm.
Pic-2
ÃÙ»-2
Cable pipe
Place the gravel 20-30 cm.depth underneath the casing for water
drainage (Pic-1).Then do the testing by filling water into the casing
and let it drain.The water should be drained out by 30 minutes.
If not,the additional drainage pipe or other system must be applied
(Pic-2)
¤ÇÃÇÒ§¡ŒÍ¹¡ÃǴ㵌¡Å‹Í§½˜§¾×é¹·ÕèÃÐÂÐÅÖ¡»ÃÐÁÒ³ 20-30 «Á. à¾×èͪ‹ÇÂÃкÒÂ
¹éíÒ·Õ跋ÇÁ¢Ñ§µÑÇâ¤Áä¿ ÊÒÁÒö·´Êͺ¡ÒÃÃкÒ¹éíÒâ´Âà·¹éíÒãʋ¡Å‹Í§ãˌàµçÁ
¹éíҨеŒÍ§ÃкÒÂÍÍ¡ËÁ´ÀÒÂã¹àÇÅÒ 30¹Ò·Õ ËÒ¡äÁ‹à»š¹µÒÁ¹Ñ鹤ÇÃÁÕ¡Òõ‹Í
·‹ÍÃкÒ¹éíÒà¾ÔèÁàµÔÁ
Water drainage pipe
·‹Í¹éíÒ·Ôé§
Installation should not be done under high humidity enviroment i.e.
rainy day or after the rain,foggy weather....ect.
äÁ‹¤ÇõԴµÑé§â¤Áä¿ã¹ª‹Ç§·ÕèÁ¤Õ ÇÒÁª×é¹Ê٧ઋ¹ Çѹ·Õè½¹µ¡µÅÍ´ËÃ×͵ԴµÑé§ËÅѧ
½¹ËÂØ´µ¡à¾ÃÒШзíÒãˌ¤ÇÒÁª×鹶١¢Ñ§änj㹵ÑÇâ¤Áä¿ËÅѧ¨Ò¡¹Ñ鹨Ðà¡Ô´¡ÒÃ
¤Çºá¹‹¹à»š¹ÅÐÍͧËÃ×ÍË´¹éíÒà¡ÒеԴºÃÔàdz㵌¡ÃШ¡ÀÒÂã¹µÑÇâ¤Áä¿
30-60 min
After connected and focussing the lighting, customer must turn on lamp
for about 30-60 minutes to allow the humidity inside to reduce. After
that close cover immediately.
ËÅѧ¨Ò¡·íÒ¡Òõ‹ÍÊÒÂä¿áÅеԴµÑé§â¤Áä¿àÊÃç¨ÊÁºÙó¤ÇÃແ´ä¿·Ôé§änj»ÃÐÁÒ³ 30-60
¹Ò·Õà¾×èÍäŋ¤ÇÒÁª×é¹ÀÒÂã¹µÑÇâ¤Áä¿¡‹Í¹·Õè¨Ð»´Ë¹ŒÒâ¤Á俷ѹ·Õ
Do not let the exposed part of the fittings be covered by the soil,dried weed or
foliage as well as corrosive or aggressive substancechemicals.
Í‹һŋÍÂãˌÁÕÊÔè§Ê¡»Ã¡àª‹¹ àÈÉ´Ô¹ ãºäÁŒ ËÃ×Í
Ë­ŒÒáˌ§ÃÇÁ¶Ö§à¤ÁÕ·Õè໚¹ÊÒÃ-¡Ñ´¡Ã‹Í¹ÁÒ»¡¤ÅØÁÊÐÊÁºÃÔàdz˹ŒÒ¾×é¹¼ÔǵÑÇâ¤Áä¿
Do not throw or drop any hard objects onto the top of fittings.
Í‹ÒãˌÇѵ¶Ø·Õè໚¹¢Í§á¢ç§Ëŋ¹ ËÃ×͵¡¡ÃÐá·¡ãʋºÃÔàdz˹ŒÒ¾×é¹¼ÔǢͧµÑÇâ¤Á
The surface temperature of the fitting can be very high after continuation in
service.
àÁ×èÍແ´ä¿·Ôé§änjã¹ÃÐÂÐàÇÅÒ˹Ö觨Ðà¡Ô´¤ÇÒÁÌ͹ÊÐÊÁºÃÔàdz´ŒÒ¹º¹¢Í§µÑÇâ¤Á俤ÇÃÃÐÁÑ´ÃÐÇѧ¡ÒÃ
ÊÑÁ¼Ñʶ١ºÃÔàdz´Ñ§¡Å‹ÒÇ
Proper use of this fitting must be observed.
¤ÇþԨÒóҤÇÒÁàËÁÒÐÊÁ¢Í§¾×é¹·Õè​ËÃ×͵íÒá˹‹§·Õè¨ÐµÔ´µÑ駵ÑÇâ¤Áä¿ µÑÇÍ‹ҧ ઋ¹ ÁÕ
¹éíҢѧ໚¹»ÃШíÒ㹺ÃÔàdz¹Ñé¹ËÃ×ÍäÁ‹? , Çѵ¶Øµ‹Ò§æ ઋ¹
´Ô¹,àÈÉãºäÁŒãºË­ŒÒÁÕâÍ¡ÒÈ·Õè¨ÐÁÒ»¡¤ÅØÁÊÐÊÁº¹Ë¹ŒÒâ¤Á໚¹»ÃÔÁÒ³ÁÒ¡ËÃ×ÍäÁ‹?
áÅÐäÁ‹¤ÇõԴµÑé§ã¹ºÃÔàdz·ÕèÍÒ¨ÁÕâÍ¡Òȶ١ÊÑÁ¼ÑÊâ´Â¤¹ â´Â੾ÒÐà´ç¡àÅç¡ËÃ×ÍÊѵǏàÅÕé§
Last Revised On : 26/03/2024 REV.10
4/5
FR-DD-29 REV.00 EFF11/03/24
YES/¶Ù¡µŒÍ§
NO/äÁ‹¶Ù¡µŒÍ§
NO/äÁ‹¶Ù¡µŒÍ§
Only for self-shielded protective lamps.
â¤Áä¿·ÕèÍ͡ẺÊíÒËÃѺ㪌¡ÑºËÅÍ´ ·ÕèÁÕ¡ÒäÃͺ»‡Í§¡Ñ¹ËÅÍ´
Any damaged safety glass cover must be replaced only with the original
spare part.
àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËŋ᷌¨Ò¡¼ÙŒ¼ÅԵ෋ҹÑé¹
NO
Not using chemical compounds and aggressive agents such as , weed repellents
fertilizers , acid solvent and contaminated irrigation water near the Luminaires.
ˌÒÁ㪌ÊÒÃà¤ÁÕઋ¹ »Ø‰Â, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໚¹¡Ã´ áÅйéíÒ»¹à»„œÍ¹ÊÒÃà¤ÁÕ
ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿
Walk over fittings.Max 1000 Kg pressure load.
¤Ã§ÊÌҧ¢Í§â¤Á俪¹Ô´¹ÕéÊÒÁÒöà´Ô¹àËÂÕºº¹Ë¹Œ​Òâ¤Á䴌 áÅÐÃѺáç¡´·Ñºä´Œ 1,000 ¡¡.
NO
NO
Clean the products regularly to maintain good light output and prolong surface
quality .
Only use solvent-free cleaning solutions on the products.
·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ±à»š¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁʋͧÊNjҧ·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ
㪌¹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁ‹ÁÕáÍÅ¡ÍÎÍŏËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·‹Ò¹Ñé¹
Do not use a high pressure washer to clean the products.
ˌÒÁ㪌à¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ±
Environmental protection: Waste electrical products should not be disposed of
with household waste. please recycle where facilities exist.check with your local
authority or retailer for recycling advice According to directive 2002/96/CE and
directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE).
ˌÒÁ·Ô駼ÅÔµÀѳ±¹ÕéËÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪌§Ò¹â»Ã´á¡¼ÅÔµÀѳ±ÍÍ¡
¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍ‹ҧàËÁÒÐÊÁà¾×èÍʋ§àÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪌«éíÒ«Ö觨Ъ‹ÇÂ
»‡Í§¡Ñ¹ÍѹµÃÒµ‹ÍÊÔè§áǴŌÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹Øɏ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁ‹ÁÕ¡ÒäǺ¤ØÁ
͌ҧÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and
Electronic Equipment (WEEE).
Last Revised On : 26/03/2024 REV.10
5/5
FR-DD-29 REV.00 EFF11/03/24
">