Unilamp ARC Mode d'emploi

INSTALLATION MANUAL
PRODUCT NAME : ARC
IP67
1.
220-240V~50-60Hz
Ordering Code
Glass Temperature
-
Input voltage
No.
64.5°C at Ta 40°C
2.
9060-C/D-3/4/5-506-91
84°C at Ta 50°C
3.
9060-A-3/4/5-768-91
64.5°C at Ta 40°C
4.
9060-C/D-3/4/5-887-91
84°C at Ta 50°C
5.
9060-A-3/4/5-769-91
64.5°C at Ta 40°C
6.
9060-C/D-3/4/5-891-91
84°C at Ta 50°C
7.
9060-A-3/4/5-710-91
69°C at Ta 25°C
8.
9060-C/D-3/4/5-505-91
71.5°C at Ta 30°C
9.
9060-A-3/4/5-719-91
69°C at Ta 25°C
10.
9060-C/D-3/4/5-902-91
71.5°C at Ta 30°C
11.
9060-A-3/4/5-720-91
69°C at Ta 25°C
13
12.
9060-C/D-3/4/5-905-91
71.5°C at Ta 30°C
13. RGBW LED Constant Current Driver
LowVoltage 500mA,
4CHx8.9Vdc-11.4Vdc, Uin max
150Vdc
( Output from SELV system only)
( ¡ÃÐáÊ俵ŒÍ§ÁÒ¨Ò¡Ãкºáç´Ñ¹ ä¿¿‡ Ò
µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂà¾Õ§෋ҹÑé¹ )
9060-A/B/C-2/4-440-91
60°C at Ta 40°C
Light Emitting Diodes
(LED)
+
9060-A-3/4/5-767-91
1-12
Light Emitting Diodes
(LED)
2
2.2
û240
25 °
2.1
200
1
2.6
û260
2.3
360°
3.A
Cable pipe
·‹ÍÊÒÂä¿
Ø 330
204
25
Water drainage pipe
·‹Í¹éíÒ·Ôé§
Last Revised On : 28/11/2023 REV.04
2.4
Cable length200 mm.
ÊÒÂä¿ÂÒÇ 200 ÁÁ.
2.5
Wood/äÁŒ
200-300
1/7
FR-DM-17 REV.03 EFF 15/09/17
4
3.B
3.B.5 concrete
¤Í¹¡ÃÕµ
Detail : A
For on-off system. /ÊíÒËÃѺÃкºà»´-»´
IP68 water tight connecting device 3 Pole.
Cable Diameter 5.0-9.5mm.
Available Separately
ªØ´¢ŒÍµ‹ÍÊÒÂ信ѹ¹éíÒ IP68, ÊíÒ ËÃѺ ÊÒÂä¿ 3ÊÒÂ
ᡨíÒ Ë¹‹Òµ‹Ò§ËÒ¡
Ordering Code : 0411-0-9-000-00
4.4
For 1-10V dimming and DALI system.
ÊíÒËÃѺÃкº´ÔÁ1-10VáÅÐÃкºDALI
4.1
IP68 water tight connecting device 5 Pole.
Cable Diameter 7.1-13mm.
Available Separately/ªØ´¢ŒÍµ‹ÍÊÒÂ信ѹ¹éíÒ IP68,
ÊíÒËÃѺÊÒÂä¿ 5 ÊÒÂ
ᡨíÒ Ë¹‹Òµ‹Ò§ËÒ¡
Ordering Code : 0413-0-9-000-00
'See connecting detail on manual.'
´Ùà ÒÂÅÐàÍÕ´·Õè¤ Ù‹Á×Í¡ÒõԴ
3.B.1
3.B.3
A
B 4.1
3.B.2
3.B.4
Detail : B
Please note the
ground level.
¢ŒÍ¤ÇÃÃÐÇѧ: ¼ÔÇ˹ŒÒ¢Í§
µÑÇâ¤Á¡Ñº¼ÔǾ×鹤ÇÃÍÂًã¹
ÃйҺà´ÕÂǡѹ
Cover protect concrete into
a water drainage pipe.
½Ò¤Ãͺ»‡Í§¡Ñ¹¤Í¹¡Ãյࢌҷ‹Í
ÃкÒ¹éíÒ
1
3
4
2
Lock the screws
following this sequence.
¤ÇâѹʡÃÙµÒÁÅíҴѺ¢Í§
ËÁÒÂàÅ¢·ÕèÃкØänjµÒÁÃÙ»ÀÒ¾
5
4.2
4.3
4.3
Torque/áçºÔ´ : 2.5 Nm.
Torque/áçºÔ´ : 2.5 Nm.
Installation complete
µÔ´µÑé§àÊÃç¨ÊÁºÙó
How to adjust the aiming angle.
ÇÔ¸Õ¡ÒûÃѺͧÈÒ
10 °
5°
2.5 °
25 °
Top View
Detail : A
Adjustable optic unit.
ÊÒÁÒö»ÃѺµíÒá˹‹§ä´ŒµÒÁ¤‹Ò·ÕèÃкØ
Last Revised On : 28/11/2023 REV.04
2/7
A
FR-DM-17 REV.03 EFF 15/09/17
For DALI RGBW (Remote Driver) remark: use with 9060-A/B/C-2-440-91
ÊíÒËÃѺ ÃкºDALI RGBW(ÃÕâÁ· ä´ÃàÇÍÏ) ËÁÒÂà˵Ø:㪌ÊíÒËÃѺ 9060-A/B/C-2-440-91
Number on the cable/ËÁÒÂàÅ¢º¹ÊÒÂä¿
A = 38-40 mm.
B = 8-10 mm.
-
2 :
3 :
4 :
5 :
1 :
B
w+
A
B+
Output to Luminaire 4x500mA
G+
R+
Input 220-240V
ÊíÒËÃѺÊÒÂࢌÒ
L
A = 45-48 mm.
B = 8-10 mm.
C = 38-40 mm.
B
C
Cable Size/¢¹Ò´ÊÒÂä¿ : 5x1.00 mm.2 Ø8-13 mm.
DA1
W+
-
A
N
DA2
R+
G+
B+
Green/Yellow :
Brown : L
Blue : N
White : DA1
Black : DA2
Accessory available separately./ÍØ»¡Ã³àÊÃÔÁ¨íÒ˹‹ÒÂᡵ‹Ò§ËÒ¡
Ordering Code
Product Name
AUN-DRG-0020-01
RGBW LED Constant Current Driver
4x500mA 4x18W (DALI)
the luminaire
Luminaire Wattage Maximum quantity of luminaire Distance from
to Driver
24W
1
10m.
Wiring diagram DMX RDM decoder. remark: use with 9060-A/B/C-D-440-91
¡Òõ‹Íǧ¨Ã DMX RDM decoder.ËÁÒÂà˵Ø:㪌ÊíÒËÃѺ 9060-A/B/C-D-440-91
Warning
Please ensure that the led lamp is connected to the driver correctly.
Wrong polarity connection cause a damage to the led lamp and driver.
â»Ã´ÃÐÇѧ¡Òõ‹ÍÊÒÂä¿ÊÅѺ ¢ÑéÇ +ºÇ¡ -ź ¨Ò¡ä´ÃàÇÍÏÁÒࢌҷÕèËÅÍ´ LED ËÒ¡µ‹ÍÊÅѺ¢ÑéÇ
¨Ð·íÒãˌä´ÃàÇÍÏá ÅÐËÅÍ´ LED à¡Ô´¤ÇÒÁàÊÕÂËÒÂ
Input 220-240 V ~
L
AC
DC
N
Output/ÍÍ¡
24 V
5core cable
Mark 1 : +
Mark 2 : RMark 3 : GMark 4 : BMark 5: W-
( Output from SELV system only)
(¡ÃÐáÊ俵ŒÍ§ÁÒ¨Ò¡Ãкºáç´Ñ¹ ä¿¿‡Ò
µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂà¾Õ§෋ҹÑé¹ )
DRIVER
DMX controller
No. Accessory available separately./ÍØ»¡Ã³àÊÃÔÁ¨íÒ˹‹ÒÂᡵ‹Ò§ËÒ¡
Ordering Code
1.
RGBW LED Constant Current DMX512, RDM Decoder
4x500mA 4x16W In IP67 GFR Polymer Box.
AUN-DRG-0113-01
2.
RGBW LED Constant Current DMX512, RDM Decoder
4x700mA 4x23W In IP67 GFR Polymer Box.
AUN-DRG-0112-01
Follow common DMX wiring practices such as termination,topology and cable specification.
»¯ÔºÑµÔµÒÁÇÔ¸Õ¡ÒÃà´Ô¹ÊÒ¢ͧ Ãкº DMX ઋ¹ ¡ÒÃàª×èÍÁµ‹Í , Ãкºà¤Ã×Í¢‹Ò áÅÐ Ê໤¢Í§ÊÒÂä¿
Last Revised On : 28/11/2023 REV.04
3/7
FR-DM-17 REV.03 EFF 15/09/17
Remark :
ËÁÒÂà˵Ø
1. Installation should be carried out by a qualified
electrician in accordance with appropriate national
wiring regulation.
¡ÒõԴµÑé§â¤Áä¿¿‡ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´Âª‹Ò§ä¿¿‡Ò
·ÕèÁÕ¤ÇÒÁÃٌáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿‡Ò
â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿‡Ò
2. Disconnect the power before changing the lamp.
»´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿
3. For Class1 luminaire, the installation must be
completed with earthing.
ÊíÒËÃѺâ¤Áä¿·ÕèÁÕ¡Òû‡Í§¡Ñ¹ä¿¿‡ÒÃÑèÇÃдѺ1
¡ÒõԴµÑ駵ŒÍ§µ‹ÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑ´ŒÇÂ
4. Do not exceed the maximum wattage.
ˌÒÁ㪌ËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡Ç‹Ò·ÕèÃÐºØ ËÃ×Í㪌ËÅÍ´¼Ô´»ÃÐàÀ·
5. Don't touch LED while maintaining or cleaning.
ˌÒÁÊÑÁ¼ÑÊËÅÍ´ LED ¢³ÐºíÒÃاÃÑ¡ÉÒ ËÃ×Í·íÒ¤ÇÒÁÊÐÍÒ´
Warning :
¢ŒÍ¤ÇÃÃÐÇѧ
1. The manufacturer will not be liable or held responsible
for any incorrect installation, misuse or improper use
and unauthorised modification to the fittings. Failure
to comply with mentioned warning may cause serious
damage or serious injury to persons, animals or
objects. If any modification is required please consult
your dealer for the details.
·Ò§¼ÙŒ¼ÅÔµäÁ‹ÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡¡ÒÃ
µÔ´µÑé§äÁ‹¶Ù¡ÇÔ¸Õ, 㪌§Ò¹¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Áã¹·Ø¡¡Ã³Õ
«Öè§ ÊÔ觼Դ»¡µÔàËŋҹÕé ÍÒ¨·íÒãˌà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊѵǏ ÊÔ觢ͧ
ËÒ¡ÁÕ¢ŒÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµŒÍ§¡ÒûÃѺᵋ§µÑÇâ¤Á
ãˌàËÁÒÐÊÁ¡Ñº¡ÒÃ㪌§Ò¹ ¡Ãس ÒµÔ´µ‹ÍµÑÇá·¹¨íÒ˹‹ÒÂËÃ×ͼٌ¼ÅÔµ
2. Where damage has occured to the fittings, please
make the replacement with standard parts before use.
㹡óշÕèÁÕªÔé¹Ê‹Ç¹»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡Ãس Òà»ÅÕ蹪Ôé¹Ê‹Ç¹
ãËÁ‹¡‹Í¹¡ÒÃ㪌§Ò¹·Ø¡¤ÃÑé§ à¾×èͤÇÒÁ»ÅÍ´ÀÑÂ
For On-Off System.
ÊíÒËÃѺ Ãкºà»´-»´
Cable Size/¢¹Ò´ÊÒÂä¿ : 3x1.00 mm. Ø5-9.5 mm.
In case the supply cable is exposed to sunlight use UV resistant cable.
¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃἋÃѧÊÕÂÙÇÕ ÊÒÂ俵ŒÍ§ÊÒÁÒö»‡Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òû‡Í§¡Ñ¹äÁ‹ãˌ¶Ù¡ÃѧÊÕÂÙÇÕ䴌
NO
Do not touch the LED because it may shorten the life time or the LED can be
breaking down.
ˌÒÁÊÑÁ¼ÑÊËÅÍ´ LED â´Âà´ç´¢Ò´ à¾ÃÒШзíÒãˌËÅÍ´àÊ×èÍÁÊÀÒ¾
Minimum distance to lighted surface.
ÃÐÂÐˋҧ¢Ñé¹µèíÒ ¨Ò¡Ë¹ŒÒâ¤Á¶Ö§¾×é¹¼ÔÇ·Õè¶Ù¡Ê‹Í§ÊNjҧ
0.5 m
Any damaged safety glass cover must be replaced only with the original
spare part.
àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËŋ᷌¨Ò¡¼ÙŒ¼ÅԵ෋ҹÑé¹
NO
Last Revised On : 28/11/2023 REV.04
Not using chemical compounds and aggressive agents such as , weed repellents
fertilizers , acid solvent and contaminated irrigation water near the Luminaires.
ˌÒÁ㪌ÊÒÃà¤ÁÕઋ¹ »Ø‰Â, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໚¹¡Ã´ áÅйéíÒ»¹à»„œÍ¹ÊÒÃà¤ÁÕ
ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿
4/7
FR-DM-17 REV.03 EFF 15/09/17
Our products are installed with electronic components with the protection against
overvoltage according to IEC 61547. The customers have to install the additional
overvoltage protection devices (against surge, transients, etc) in their electrical
system to avoid the risk of damage. Failing to do so will end the product warranty.
¼ÅÔµÀѳ±¢Í§àÃÒÁÕ¡ÒõԴµÑé§ÍØ»¡Ã³ÍÔàÅç¡·Ã͹ԡʏÊíÒËÃѺ¡Òû‡Í§¡Ñ¹áç´Ñ¹ä¿à¡Ô¹µÒÁÁÒµÃฐÒ¹ IEC
61547 áÅÐÅÙ¡¤ŒÒµŒÍ§µÔ´µÑé§ÍØ»¡Ã³»‡Í§¡Ñ¹áç´Ñ¹ä¿à¡Ô¹à¾ÔèÁàµÔÁ (»‡Í§¡Ñ¹ä¿¡ÃЪҡ ,ä¿¿‡ÒÅѴǧ¨Ã
ÏÅÏ)ã¹Ãкºä¿¿‡Ò´ŒÇ à¾×èÍËÅÕ¡àÅÕ觤ÇÒÁàÊÕ觷Õè¨Ðà¡Ô´¤ÇÒÁàÊÕÂËÒ ËÒ¡äÁ‹´íÒà¹Ô¹¡Òôѧ¡Å‹ÒÇ
¡ÒÃÃѺ»ÃСѹ¨ÐÊÔé¹Êشŧ
LED
Clean the products regularly to maintain good light output and prolong surface
quality .
Only use solvent-free cleaning solutions on the products.
·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±à»š¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁʋͧÊNjҧ·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ
㪌¹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁ‹ÁÕáÍÅ¡ÍÎÍŏËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·‹Ò¹Ñé¹
Do not use a high pressure washer to clean the products.
ˌÒÁ㪌à¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±
For Remote driver
To replace the LED module or the entrire luminaire.Please consult your
sales representative.
ËÒ¡µŒÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ×Íâ¤Áä¿â»Ã´µÔ´µ‹ÍµÑÇá·¹¢Ò¢ͧ¤Ø³
LED
LED
For On-Off/1-10V dimming/ DALI
LED
To replace the LED module or the entrire luminaire.Please consult your
sales representative.
ËÒ¡µŒÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ×Íâ¤Áä¿â»Ã´µÔ´µ‹ÍµÑÇá·¹¢Ò¢ͧ¤Ø³
LED
LED
230 V
Environmental protection: Waste electrical products should not be disposed of
with household waste. please recycle where facilities exist.check with your local
authority or retailer for recycling advice According to directive 2002/96/CE and
directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE).
ˌÒÁ·Ô駼ÅÔµÀѳ±¹ÕéËÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪌§Ò¹â»Ã´á¡¼ÅÔµÀѳ ±ÍÍ¡
¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍ‹ҧàËÁÒÐÊÁà¾×èÍʋ§àÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪌«éíÒ«Ö觨Ъ‹ÇÂ
»‡Í§¡Ñ¹ÍѹµÃÒµ‹ÍÊÔè§áǴŌÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹Øɏ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁ‹ÁÕ¡ÒäǺ¤ØÁ
͌ҧÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and
Electronic Equipment (WEEE).
Last Revised On : 28/11/2023 REV.04
5/7
FR-DM-17 REV.03 EFF 15/09/17
Replacing the LED module
ÇÔ¸Õ¡ÒÃà»ÅÕè¹ LED module
1. Contact your sales representative for replacement LED modules. Make sure that the replacement module
match the initially supplied module. Note the part number printed on the LED module.
àµÃÕÂÁ LED module ãˌµÃ§¡ÑºÃ؋¹·Õ赌ͧ¡ÒÃà»ÅÕè¹â´ÂµÃǨÊͺ·ÕèËÁÒÂàÅ¢·Õè¾ÔÁ¾º¹LED modules áÅÐ µÔ´µ‹ÍµÑÇá·¹¢ÒÂà¾×èÍÊÑ觫×éÍ
LED modules ·Õ赌ͧ¡ÒÃà»ÅÕè¹
2. The LED module can be replaced by qualified persons using standard tools.
¡ÒÃà»ÅÕè¹ LED module µŒÍ§·íÒâ´Âª‹Ò§¼ÙŒªíÒ¹Ò­áÅÐ㪌à¤Ã×èͧÁ×Í·Õè䴌ÁÒµÃฐÒ¹
3. Disconnect power before opening the luminaire housing.
µÑ´áËŋ§¨‹ÒÂä¿¡‹Í¹·Õè¨Ðແ´µÑÇâ¤Á
4. Replace the old LED module with the new LED module. Reapply thermal interface material as supplied with the
new LED module.
¶Í´ LED module ·ÕèªíÒÃØ´ÍÍ¡ ¨Ò¡¹ÑŒ¹·íÒ¤ÇÒÁÊÐÍÒ´¨Ø´ÇÒ§ËÅÍ´ áŌǨ֧ ·íÒ¡ÒûÃСͺ LED module ãËÁ‹ áÅеŒÍ§à»ÅÕè¹
Ἃ¹Thermal Pad ËÃ×Í Thermal Grease ´ŒÇ·ء¤ÃÑé§
5. Inspect gaskets and if required replace with new gaskets. Defective luminaire covers must be replaced. Inspect
correct wiring of replaced LED module.
µÃǨÊͺ»ÃÐà¡ç¹áÅЪÔé¹Ê‹Ç¹¢Í§µÑÇâ¤Á ¶ŒÒªíÒÃØ´àÊÕÂËÒÂãˌ·íÒ¡ÒÃà»ÅÕè¹ãËÁ‹ áÅеÃǨÊͺ¡ÒÃࢌÒÊÒÂ俢ͧ LED module
·Õèà»ÅÕè¹ãËÁ‹¶Ù¡µŒÍ§ËÃ×ÍäÁ‹
6. Close the luminaire housing before reconnecting power.
»´½Ò¤ÃͺÅçͤâ¤Áä¿ãˌàÃÕºÌÍ¡‹Í¹à»´ä¿
GENERAL INSTALLATION GUIDE (HIGHLY RECOMMENDED)
¢ŒÍá¹Ð¹íÒ㹡ÒõԴµÑé§
Pic-1
ÃÙ»-1
200-300
Cable pipe
·‹ÍÊÒÂä¿
Water drainage pipe
·‹Í ¹éíÒ ·Ôé §
Pic-2
ÃÙ»-2
Place the gravel 200-300 mm.depth underneath the casing for water
drainage (Pic-1).Then do the testing by filling water into the casing
and let it drain.The water should be drained out by 30 minutes.
If not,the additional drainage pipe or other system must be applied
(Pic-2)
¤ÇÃÇÒ§¡ŒÍ¹¡ÃǴ㵌¡Å‹Í§½˜§¾×é¹·ÕèÃÐÂÐÅÖ¡»ÃÐÁÒ³ 200-300 ÁÁ. à¾×èͪ‹ÇÂÃкÒÂ
¹éíÒ·Õ跋ÇÁ¢Ñ§µÑÇâ¤Áä¿ ÊÒÁÒö·´Êͺ¡ÒÃÃкÒ¹éíÒâ´Âà·¹éíÒãʋ¡Å‹Í§ãˌàµçÁ
¹éíҨеŒÍ§ÃкÒÂÍÍ¡ËÁ´ÀÒÂã¹àÇÅÒ 30¹Ò·Õ ËÒ¡äÁ‹à»š¹µÒÁ¹Ñ鹤ÇÃÁÕ¡Òõ‹Í
·‹ÍÃкÒ¹éíÒà¾ÔèÁàµÔÁ
Do not let the exposed part of the fittings be covered by the soil,dried weed or
foliage as well as corrosive or aggressive substancechemicals.
Í‹һŋÍÂãˌÁÕÊÔè§Ê¡»Ã¡àª‹¹ àÈÉ´Ô¹ ãºäÁŒ ËÃ×Í
Ë­ŒÒáˌ§ÃÇÁ¶Ö§à¤ÁÕ·Õè໚¹ÊÒÃ-¡Ñ´¡Ã‹Í¹ÁÒ»¡¤ÅØÁÊÐÊÁºÃÔàdz˹ŒÒ¾×é¹¼ÔǵÑÇâ¤Áä¿
Do not throw or drop any hard objects onto the top of fittings.
Í‹ÒãˌÇѵ¶Ø·Õè໚¹¢Í§á¢ç§Ëŋ¹ ËÃ×͵¡¡ÃÐá·¡ãʋºÃÔàdz˹ŒÒ¾×é¹¼ÔǢͧµÑÇâ¤Á
The surface temperature of the fitting can be very high after continuation in
service.
àÁ×èÍແ´ä¿·Ôé§änjã¹ÃÐÂÐàÇÅÒ˹Ö觨Ðà¡Ô´¤ÇÒÁÌ͹ÊÐÊÁºÃÔàdz´ŒÒ¹º¹¢Í§µÑÇâ¤Á俤ÇÃÃÐÁÑ´ÃÐÇѧ¡ÒÃÊÑÁ¼Ñʶ١
ºÃÔàdz´Ñ§¡Å‹ÒÇ
Proper use of this fitting must be observed.
¤ÇþԨÒóҤÇÒÁàËÁÒÐÊÁ¢Í§¾×é¹·Õè​ËÃ×͵íÒá˹‹§·Õè¨ÐµÔ´µÑ駵ÑÇâ¤Áä¿ µÑÇÍ‹ҧ ઋ¹ ÁÕ
¹éíҢѧ໚¹»ÃШíÒ㹺ÃÔàdz¹Ñé¹ËÃ×ÍäÁ‹? , Çѵ¶Øµ‹Ò§æ ઋ¹
´Ô¹,àÈÉãºäÁŒãºË­ŒÒÁÕâÍ¡ÒÈ·Õè¨ÐÁÒ»¡¤ÅØÁÊÐÊÁº¹Ë¹ŒÒâ¤Á໚¹»ÃÔÁÒ³ÁÒ¡ËÃ×ÍäÁ‹?
áÅÐäÁ‹¤ÇõԴµÑé§ã¹ºÃÔàdz·ÕèÍÒ¨ÁÕâÍ¡Òȶ١ÊÑÁ¼ÑÊâ´Â¤¹ â´Â੾ÒÐà´ç¡àÅç¡ËÃ×ÍÊѵǏàÅÕé§
Last Revised On : 28/11/2023 REV.04
6/7
FR-DM-17 REV.03 EFF 15/09/17
Installation should not be done under high humidity enviroment i.e.
rainy day or after the rain,foggy weather....ect.
äÁ‹¤ÇõԴµÑé§â¤Áä¿ã¹ª‹Ç§·ÕèÁÕ¤ÇÒÁª×é¹Ê٧ઋ¹ Çѹ·Õè½¹µ¡µÅÍ´ËÃ×͵ԴµÑé§ËÅѧ
½¹ËÂØ´µ¡à¾ÃÒШзíÒãˌ¤ÇÒÁª×鹶١¢Ñ§änj㹵ÑÇâ¤Áä¿ËÅѧ¨Ò¡¹Ñ鹨Ðà¡Ô´¡ÒÃ
¤Çºá¹‹¹à»š¹ÅÐÍͧËÃ×ÍË´¹éíÒà¡ÒеԴºÃÔàdz㵌¡ÃШ¡ÀÒÂã¹µÑÇâ¤Áä¿
YES/¶Ù¡µŒÍ§
NO/äÁ‹¶Ù¡µŒÍ§
NO/äÁ‹¶Ù¡µŒÍ§
Luminaire withstands a maximum static load of 1000 kg.
â¤Ã§ÊÌҧ¢Í§â¤Á俪¹Ô´¹ÕéÊÒÁÒöà Ѻáç¡´·Ñºä´Œ 1,000 ¡¡.
Last Revised On : 28/11/2023 REV.04
7/7
FR-DM-17 REV.03 EFF 15/09/17
">