Unilamp AGAR Bollard Mode d'emploi

INSTALLATION MANUAL
PRODUCT NAME : AGAR Prismatic - Indirect Light Bollard
AGAR Opal - Direct Light Bollard
No.
Input voltage
1.
220-240V~ 50-60Hz **
*
**
IP65
Ordering Code
7123/7124-0-3/4/5-887-XX
7123/7124-0-3/4/5-891-XX
3.
7123/7124-0-3/4/5-506-XX
4.
7123/7124-0-3-902-XX
5.
7123/7124-0-3-905-XX
6.
7123/7124-0-3-505-XX
+
2.
220-240V~ 50-60Hz *
1-6
7-8
Light Emitting Diodes
(LED)
Light Emitting Diodes
(LED)
7123/7124-0-3-873-XX
8.
7123/7124-0-3-874-XX
Part/ªÔé¹-A
-
7.
û324
3
û324
3.3
3.2
895
895
3.1
Part/ªÔé¹-B
3.4
û175
û175
AGAR Opal - Direct Light Bollard
AGAR Prismatic - Indirect Light Bollard
Part/ªÔé¹-B
2
M8x1.25
200
1
50
Cable length 200 mm.
ÊÒÂä¿ÂÒÇ 200 ÁÁ.
1.1
û90
û115
û175
3.5
1.2
Last Revised On : 21/07/2022 REV.06
Anchor bolt kit available separately
ªØ´ÊÁͽ˜§¾×é¹ áÍÅ⺌ŷ ᡨíÒ Ë¹‹ ÒÂ
Ordering Code/ÃËÑÊÊÑ觫×éÍ : 0084-0-9-000-00
1/5
FR-DM-17 REV.03 EFF 15/09/17
4 For Class I
4 For Class II
6
4.3
25
6
6
30
2
Cable size : 3x1.00 mm. Ø8-11.5mm.
¢¹Ò´ÊÒÂä¿
4.3
5
25
2
Cable size : 2x1.00 mm. Ø8-11.5mm.
¢¹Ò´ÊÒÂä¿
5.2
4.1
4.2
4.1
4.2
Torque/áçºÔ´ : 6 Nm.
5.1
6
6 For Class II
For Class I
Part/ªÔé¹-A
Part/ªÔé¹-A
Warranty
void if removed.
ÊÔé¹ ÊØ´¡ÒÃÃѺ»ÃСѹ
ËÒ¡¶Ù¡á¡ÐÍÍ¡
6.2
6.3
6.3
Do not cut or
disconnect the
cable between
this area.
ˌÒÁµÑ ´µ‹ ÍÊÒÂä¿
ºÃÔ àdz¹Õé
Torque/áçºÔ´ : 6 Nm.
Warranty
void if removed.
ÊÔé¹ ÊØ´¡ÒÃÃѺ»ÃСѹ
ËÒ¡¶Ù¡á¡ÐÍÍ¡
6.2
Do not cut or
disconnect the
cable between
this area.
ˌÒÁµÑ ´µ‹ ÍÊÒÂä¿
ºÃÔ àdz¹Õé
Torque/áçºÔ´ : 6 Nm.
Part/ªÔé¹-B
water tight connecting device.
6.1 IP68
Available Separately
IP68 water tight connecting device.
Use the rubber seal according to the size of the cable
àÅ× Í¡ãªŒÅÙ¡ÂÒ§à¤àºÔ Åá¡Åç ¹´ µÒÁ¢¹Ò´¢Í§ÊÒÂä¿
Cable size :
¢¹Ò´ÊÒÂä¿
µÑǵ‹ÍÊÒÂä¿»‡Í§¡Ñ¹¹éíÒ ¨íÒ˹‹ÒÂᡵ‹Ò§ËÒ¡
Ordering Code/ÃËÑÊÊÑ觫×éÍ :
0248-0-9-000-00
Separately
6.1 µÑAvailable
ǵ‹Í ÊÒÂä¿»‡Í §¡Ñ¹¹éíÒ ¨íÒ Ë¹‹Ò Âᡵ‹Ò§ËÒ¡
Rubber seal size
ÅÙ¡ ÂÒ§à¤àºÔ Å á¡Åç ¹´·Õè 㪌
Ordering Code/ÃËÑÊ ÊÑè§ «×éÍ :
0248-0-9-000-00
9
Cable size Dia Ø8-9 mm.
¢¹Ò´ÊÒÂä¿
L = Brown (ÊÕ¹éíÒ µÒÅ)
5
Part/ªÔé¹-B
Cable size Dia Ø10-11.5 mm.
5
Use the rubber seal according to the size of the cable
àÅ× Í¡ãªŒÅÙ¡ÂÒ§à¤àºÔ Åá¡Åç ¹´ µÒÁ¢¹Ò´¢Í§ÊÒÂä¿
Cable size :
¢¹Ò´ÊÒÂä¿
9
Cable size Dia Ø8-9 mm.
¢¹Ò´ÊÒÂä¿
L = Brown (ÊÕ¹éíÒ µÒÅ)
12
Cable size Dia Ø10-11.5 mm.
¢¹Ò´ÊÒÂä¿
=Green and yellow (ÊÕà¢Õ ÂÇ¡Ñ ºÊÕ àËÅ× Í§) ¢¹Ò´ÊÒÂä¿
N = Blue (ÊÕ¿‡Ò)
Rubber seal size
ÅÙ¡ ÂÒ§à¤àºÔ Å á¡Åç ¹´·Õè 㪌
12
N = Blue (ÊÕ¿‡Ò)
Make sure that the rubber seal is
correctly in place.
ÃÐÇÑ § ÅÙ¡ ÂÒ§ËÅØ´ ÍÍ¡¨Ò¡ªØ ´à¤àºÔ Åá¡Åç ¹´
7
7
1
Make sure that
cable glands are
fastened.
µŒÍ§¢Ñ ¹Ê¡ÃÙãˌ á ¹‹ ¹ ·Ø ¡ µÑ Ç
2
6
10
1
2
6
4
10
4
3
Last Revised On : 21/07/2022 REV.06
3
8
9
Make sure that the rubber seal is
correctly in place.
ÃÐÇѧ ÅÙ¡ ÂÒ§ËÅØ´ÍÍ¡¨Ò¡ªØ´ à¤àºÔÅá¡Åç ¹ ´
2/5
8
9
Make sure that cable
glands are fastened.
µŒ ͧ¢Ñ ¹Ê¡ÃÙ ãˌṋ ¹·Ø ¡µÑ Ç
FR-DM-17 REV.03 EFF 15/09/17
7
Remark :
ËÁÒÂà˵Ø
1. Installation should be carried out by a qualified
electrician in accordance with appropriate national
wiring regulation.
¡ÒõԴµÑé§â¤Áä¿¿‡ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´Âª‹Ò§ä¿¿‡Ò
·ÕèÁÕ¤ÇÒÁÃٌáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿‡Ò
â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿‡Ò
2. Disconnect the power before changing the lamp.
»´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿
3. For class 1 luminaires,the installation must be
completed with earthing.
ÊíÒËÃѺâ¤ÁÃ؋¹·Õè¶Ù¡Í͡ẺáÅШѴänj㹻ÃÐàÀ·¢Í§¡Òû‡Í§¡Ñ¹ä¿ÃÑèÇ
ÃдѺ1 ¡ÒõԴµÑ駵ŒÍ§µ‹ÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑÂ
4. Do not exceed the maximum wattage.
ˌÒÁ㪌ËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡Ç‹Ò·ÕèÃÐºØ ËÃ×Í㪌ËÅÍ´¼Ô´»ÃÐàÀ·
5. Don't touch LED while maintaining or cleaning.
ˌÒÁÊÑÁ¼ÑÊËÅÍ´ LED ¢³ÐºíÒÃاÃÑ¡ÉÒ ËÃ×Í·íÒ¤ÇÒÁÊÐÍÒ´
Installation complete
¡ÒõԴµÑé§àÊÃç¨ÊÁºÙó
Warning :
¢ŒÍ¤ÇÃÃÐÇѧ
1. The manufacturer will not be liable or held responsible for any incorrect installation, misuse or improper use and
unauthorised modification to the fittings. Failure to comply with mentioned warning may cause serious damage or
serious injury to persons, animals or objects. If any modification is required please consult your dealer for the details.
·Ò§¼ÙŒ¼ÅÔµäÁ‹ÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡¡ÒõԴµÑé§äÁ‹¶Ù¡ÇÔ¸Õ, 㪌§Ò¹¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Áã¹·Ø¡¡Ã³Õ «Öè§
ÊÔ觼Դ»¡µÔàËŋҹÕé ÍÒ¨·íÒãˌà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊѵǏ ÊÔ觢ͧ ËÒ¡Á Õ¢ŒÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµŒÍ§¡ÒûÃѺᵋ§µÑÇâ¤Á ãˌàËÁÒÐÊÁ¡Ñº¡ÒÃ㪌§Ò¹
¡Ãس ÒµÔ´µ‹ÍµÑÇá·¹¨íÒ˹‹ÒÂËÃ×ͼٌ¼ÅÔµ
2. Where damage has occured to the fittings, please make the replacement with standard parts before use.
㹡óշÕèÁÕªÔé¹Ê‹Ç¹»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡Ãس Òà»ÅÕ蹪Ôé¹Ê‹Ç¹ãËÁ‹¡‹Í¹¡ÒÃ㪌§Ò¹·Ø¡¤ÃÑé§ à¾×èͤÇÒÁ»ÅÍ´ÀÑÂ
For 1-10V dimming and DALI system.
ÊíÒËÃѺÃкº´ÔÁ1-10V áÅÐÃкºDALI
A
A = 38-40 mm.
B = 8-10 mm.
C = 30-32 mm.
Cable Size/¢¹Ò´ÊÒÂä¿ : 5x1.00 mm.2 Ø7.1-13 mm.
B
C
Green/Yellow (ÊÕà¢ÕÂÇ/ÊÕàËÅ×ͧ) :
Brown (ÊÕ¹éíÒµÒÅ) : L
Blue (ÊÕ¹éíÒà§Ô¹) : N
White (ÊÕ¢ÒÇ) : + (DA1)
Black (ÊÕ´íÒ) : - (DA2)
IP68 water tight connecting device 5 Pole.Cable Diameter 7.1-13 mm.
Available Separately/µÑǵ‹ÍÊÒÂä¿»‡Í§¡Ñ¹¹éíÒ ¨íÒ˹‹ÒÂᡵ‹Ò§ËÒ¡
Ordering Code : 0413-0-9-000-00
Last Revised On : 21/07/2022 REV.06
3/5
FR-DM-17 REV.03 EFF 15/09/17
For Class I
Cable Size/¢¹Ò´ÊÒÂä¿ : 3x1.00 mm.2 Ø8-11.5 mm.
For Class II
Cable Size/¢¹Ò´ÊÒÂä¿ : 2x1.00 mm.2 Ø8-11.5 mm.
In case the supply cable is exposed to sunlight use UV resistant cable.
¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃἋÃѧÊÕÂÙÇÕ ÊÒÂ俵ŒÍ§ÊÒÁÒö»‡Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òû‡Í§¡Ñ¹äÁ‹ãˌ¶Ù¡ÃѧÊÕÂÙÇÕ䴌
Do not touch the LED because it may shorten the life time or the LED can be
breaking down.
ˌÒÁÊÑÁ¼ÑÊËÅÍ´ LED â´Âà´ç´¢Ò´ à¾ÃÒШзíÒãˌËÅÍ´àÊ×èÍÁÊÀÒ¾
NO
Any damaged safety glass cover must be replaced only with the original
spare part.
àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËŋ᷌¨Ò¡¼ÙŒ¼ÅԵ෋ҹÑé¹
NO
LED
Not using chemical compounds and aggressive agents such as , weed repellents
fertilizers , acid solvent and contaminated irrigation water near the Luminaires.
ˌÒÁ㪌ÊÒÃà¤ÁÕઋ¹ »Ø‰Â, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໚¹¡Ã´ áÅйéíÒ»¹à»„œÍ¹ÊÒÃà¤ÁÕ
ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿
Our products are installed with electronic components with the protection against
overvoltage according to IEC 61547. The customers have to install the additional
overvoltage protection devices (against surge, transients, etc) in their electrical
system to avoid the risk of damage. Failing to do so can cause the end
of products warranty.
¼ÅÔµÀѳ±¢Í§àÃÒ䴌ÃѺ¡ÒõԴµÑé§Ãкº»‡Í§¡Ñ¹áç´Ñ¹ä¿¿‡Òà¡Ô¹µÒÁÁÒµÃฐÒ¹ IEC 61547
ÅÙ¡¤ŒÒµŒÍ§µÔ´µÑé§ÍØ»¡Ã³»‡Í§¡Ñ¹áç´Ñ¹ä¿¿‡Òà¡Ô¹à¾ÔèÁàµÔÁ(ઋ¹ »‡Í§¡Ñ¹ä¿¡ÃЪҡ ÏÅÏ )
ã¹Ãкºä¿¿‡Òà¾×èÍËÅÕ¡àÅÕ觤ÇÒÁàÊÕÂËÒ·ÕèÍÒ¨¨Ðà¡Ô´¢Öé¹ ËÒ¡ÅÙ¡¤ŒÒäÁ‹·íÒ¡ÒõԴµÑé§à¾ÔèÁ
àµÔÁÍÒ¨·íÒãˌ¡ÒÃÃѺ»ÃСѹÊÔ¹¤ŒÒÊÔé¹Êشŧ
Clean the products regularly to maintain good light output and prolong surface
quality .
Only use solvent-free cleaning solutions on the products.
·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±à»š¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁʋͧÊNjҧ·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ
㪌¹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁ‹ÁÕáÍÅ¡ÍÎÍŏËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·‹Ò¹Ñé¹
Last Revised On : 21/07/2022 REV.06
4/5
FR-DM-17 REV.03 EFF 15/09/17
Do not use a high pressure washer to clean the products.
ˌÒÁ㪌à¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±
LED
LED
To replace the LED module or the entrire luminaire.Please consult your
sales representative.
ËÒ¡µŒÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ× Íâ¤Áä¿â»Ã´µÔ´µ‹ÍµÑÇá·¹¢Ò¢ͧ¤Ø³
LED
230 V
Environmental protection: Waste electrical products should not be disposed of
with household waste. please recycle where facilities exist.check with your local
authority or retailer for recycling advice According to directive 2002/96/CE and
directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE).
ˌÒÁ·Ô駼ÅÔµÀѳ±¹ÕéËÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪌§Ò¹â»Ã´á¡¼ÅÔµÀѳ ±ÍÍ¡
¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍ‹ҧàËÁÒÐÊÁà¾×èÍʋ§àÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪌«éíÒ«Ö觨Ъ‹ÇÂ
»‡Í§¡Ñ¹ÍѹµÃÒµ‹ÍÊÔè§áǴŌÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹Øɏ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁ‹ÁÕ¡ÒäǺ¤ØÁ
͌ҧÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and
Electronic Equipment (WEEE).
Replacing the LED module
ÇÔ¸Õ¡ÒÃà»ÅÕè¹ LED module
1. Contact your sales representative for replacement LED modules. Make sure that the replacement module
match the initially supplied module. Note the part number printed on the LED module.
àµÃÕÂÁ LED module ãˌµÃ§¡ÑºÃ؋¹·Õ赌ͧ¡ÒÃà»ÅÕè¹â´ÂµÃǨÊͺ·ÕèËÁÒÂàÅ¢·Õè¾ÔÁ¾º¹LED modules áÅÐ µÔ´µ‹ÍµÑÇá·¹¢ÒÂà¾×èÍÊÑ觫×éÍ
LED modules ·Õ赌ͧ¡ÒÃà»ÅÕè¹
2. The LED module can be replaced by qualified persons using standard tools.
¡ÒÃà»ÅÕè¹ LED module µŒÍ§·íÒâ´Âª‹Ò§¼ÙŒªíÒ¹Ò­áÅÐ㪌à¤Ã×èͧÁ×Í·Õè䴌ÁÒµÃฐÒ¹
3. Disconnect power before opening the luminaire housing.
µÑ´áËŋ§¨‹ÒÂä¿¡‹Í¹·Õè¨Ðແ´µÑÇâ¤Á
4. Replace the old LED module with the new LED module. Reapply thermal interface material as supplied with the
new LED module.
¶Í´ LED module ·ÕèªíÒÃØ´ÍÍ¡ ¨Ò¡¹ÑŒ¹·íÒ¤ÇÒÁÊÐÍÒ´¨Ø´ÇÒ§ËÅÍ´ áŌǨ֧ ·íÒ¡ÒûÃСͺ LED module ãËÁ‹ áÅеŒÍ§à»ÅÕè¹
Ἃ¹Thermal Pad ËÃ×Í Thermal Grease ´ŒÇ·ء¤ÃÑé§
5. Inspect gaskets and if required replace with new gaskets. Defective luminaire covers must be replaced. Inspect
correct wiring of replaced LED module.
µÃǨÊͺ»ÃÐà¡ç¹áÅЪÔé¹Ê‹Ç¹¢Í§µÑÇâ¤Á ¶ŒÒªíÒÃØ´àÊÕÂËÒÂãˌ·íÒ¡ÒÃà»ÅÕè¹ãËÁ‹ áÅеÃǨÊͺ¡ÒÃࢌÒÊÒÂ俢ͧ LED module
·Õèà»ÅÕè¹ãËÁ‹¶Ù¡µŒÍ§ËÃ×ÍäÁ‹
6. Close the luminaire housing before reconnecting power.
»´½Ò¤ÃͺÅçͤâ¤Áä¿ãˌàÃÕºÌÍ¡‹Í¹à»´ä¿
Last Revised On : 21/07/2022 REV.06
5/5
FR-DM-17 REV.03 EFF 15/09/17
">