7808835 | 8646291 | Owner's manual | West Marine 7808827 m-Series Mini Battery Switches Manuel du propriétaire

Specifications
Marine Electrical Products
m-Series Dual Circuit Plus™ Battery Switch
PN 6011
Inrush Rating: 2.5 sec.
Cranking Rating: 100 sec.
Intermittent Rating: 5 min. (UL 1107)
Continuous Rating: (UL 1107)
Terminal Stud, Tin-Plated Copper
Torque
Cable Size to Meet Ratings*
Maximum Voltage Rating
Ignition Protected
marked
1200 Amperes DC
600 Amperes DC
450 Amperes DC
300 Amperes DC
3/8”-16 (M10)
120 in-lb (13.56 N·m)
4/0 AWG (95mm²)
32 Volts DC
Agency Specifications
• Meets all American Boat and Yacht Council (ABYC) requirements for
battery switches
• UL Listed - UL 1107 for electric power switches
• Meets UL 1500 and SAE J1171 external ignition protection requirements
Switch Set to "ON"
Switch Set to
"COMBINE BATTERIES"
Features
Guarantee
Any Blue Sea Systems product with which a customer is not satisfied may be
returned for a refund or replacement at any time.
• Isolates Start and House circuits, and combines both battery banks for
emergency starting
Tin-plated copper studs:
• 3/8”-16 (M10) provide maximum conductivity and corrosion resistance
• One-piece to reduce risk of overheating
• 7/8” (22.22mm) length to accept multiple cable terminals
Case design:
• Allows surface mounting, front or rear panel mounting
• Accepts up to 4/0 AWG (95mm²) battery cables
• Removable knob for security and service lockout
• Removable isolator covers protect rear contacts
For information about Blue Sea Systems Engine Starting Standard, go to
www.bluesea.com.
* Reducing cable sizes will reduce current ratings
Blue Sea Systems Inc.
425 Sequoia Drive
Bellingham, WA 98226 USA
Phone (360) 738-8230
Fax (360) 734-4195
E-mail conductor@bluesea.com
www.bluesea.com
Caution
•
•
•
•
Disconnect positive battery terminal before installing.
Débranchez la cosse positive de la batterie avant de l’installer.
Desconecte el terminal positivo de la batería antes de la instalación.
Prima di eseguire l’installazione, disconnettere il terminale positivo della batteria.
•
•
•
•
Consult marine electrical professional for proper wiring application.
Consultez un professionnel de l’électricité marine pour installer le câblage correctement.
Consulte a un electricista marino profesional para la aplicación de alambrado apropiada.
Per assicurarsi che i cavi siano correttamente collegati, rivolgersi ad un elettricista specializzato in motori marini.
Installation
• Refer to the latest edition of NFPA 302 and/or ABYC E11 Standard for installation information.
•
•
•
•
Attach one 4/0 AWG cable per terminal to meet ratings.
Raccordez un câble 95mm² par cosse pour respecter les spécifications.
Sujete un cable 95mm² por terminal de acuerdo a la clasificación.
Attaccare un cavo 95mm² per conformarsi alle tarature.
•
•
•
•
Battery cable terminals must be attached under nut and lock washer. Torque 120 in-lb (13.56 N·m).
Les cosses des câbles de batterie doivent être fixées sous la rondelle de sûreté et l’écrou – couple de serrage de 13,56 N·m (120 lb-po).
Los terminales de los cables de batería deberán ser sujetados debajo de la tuerca y la arandela. Apriételos a una torsión de 13,56 N·m (120 lbs-pul).
I terminali del cavo della batteria vanno attaccati con un dado e una rondella elastica: coppia di 13,56 N·m (120 lbs-in).
Operation
•
•
•
•
Turn all appliances off before turning the battery switch to OFF.
Éteignez tous les appareils électriques avant de mettre l’interrupteur de batterie sur ARRÊT.
Apague todos los artefactos antes de girar el interruptor de batería a APAGADO (OFF).
Spegnere tutte le apparecchiature prima di muovere l’interruttore della batteria su OFF (spento).
•
•
•
•
Do not switch to OFF while engine is running.
Ne le mettez pas sur ARRÊT alors que le moteur tourne.
No coloque el interruptor en APAGADO (OFF) mientras que el motor esté funcionando.
Non muovere l’interruttore su OFF (spento) quando il motore è in moto.
1.900"
48.26mm
Surface mounting
0.750"
19.05mm
BULKHEAD
PANEL
Front panel mounting
Switch Mounting Options
Cutout
Dimension
2 5/8"
(67mm)
Cutout
Dimension
2 5/16" (59mm)
2.175"
56.24mm
#10 (M5)
screw
2.175"
56.24mm
m-Series Battery Switch Dimensions
1
1
2
2
Starter
or other load
0.125"
3.18mm
1.930"
49.02mm
Rear panel mounting