Installation manuel | Halsey Taylor 8221080883 Double Bubbler™ Lead Law Compliant 8 Gallon FS Stainless Steel Water Cooler E/PRF Guide d'installation

XP8WQ*1D
Owners Manual
FLOOR MOUNT WATER COOLER
PAGE 1
0000001091 (Rev. A - 02/16)
XP8WQ*1D
Note: Danger! Electric shock hazard. Disconnect power before servicing unit.
Uses HFC-134A refrigerant
4, 7, 16
6
8
1, 2
17
22
SEE FIG. 3
31
26
25
21
23
32
15, 18
20
33
3
27
19
28
12
13, 14
29
30
FIG. 1
0000001091 (Rev. A - 02/16)
PAGE 2
PAGE 3
FIG. 2
LEGEND/LEYENDA/LÉGENDE
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38mm) OUT
WALL. ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA
FROM WALL SHUT OFF BY OTHERS
ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-1/2"
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE L’ENCEINTE
(38mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
ET LE MUR.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
F = WALL SCREW HOLES
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
AGUJEROS DE TORNILLOS DE PARED
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
TROUS DE VIS DU MUR
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼” DE DIÁMETRO.
G = 2 X 4 BLOCKING
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE D’EAU.
BLOQUEO DE 2 X 4
C = 1-1/4 TRAP NOT FURNISHED**
BLOC 2 X 4
PURGADOR DE 1¼ NO PROPORCIONADO**
SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD
EMPLACEMENT DE LA PRISE DE COURANT
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
XP8WQ*1D
0000001091 (Rev. A - 02/16)
XP8WQ*1D
PUSH BUTTON VALVE ADJUSTMENT
6
24
5
10
STREAM HEIGHT
ADJUSTMENT SCREW
11
9
ADJUST THIS SCREW TO ELIMINATE VALVE LEVER "FREE PLAY"
OR CONTINUOUS FLOW FROM BUBBLER
FIG. 3
CONDENSER WATER VALVE ADJUSTMENT
The condenser water valve is factory preset for a condenser water outlet temperature of 95° to 105° F.
If actual temperature varies greatly from this, readjust water flow rate at the valve using the following procedures.
1. START UP COMPRESSOR
This can be accomplished by depressing the cooler push button (See Fig. 1 - Item 2). Keep water
running during the entire readjustment procedure.
2. ADJUSTMENT CONDENSER WATER VALVE
Adjust valve by rotating adjustment stem. Rotating stem clockwise will increase water flow.
Counterclockwise rotation will decrease water flow. Increasing water flow will result in a lower
condenser outlet temperature, while decreasing water flow will result in a higher outlet temperature.
Proper adjustment is attained when condenser outlet temperature is 95° to 105° F.
FIG. 4
CORRECT STREAM HEIGHT
FIG. 5
0000001091 (Rev. A - 02/16)
PAGE 4
XP8WQ*1D
PARTS LIST 115V
ITEM
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12*
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
NS
101452331870
601451151550
28368C
102639931640
98531C
98533C
160270508640
28461C
26860C
26861C
26862C
36220C
35797C
35803C
600793851550
98683C
75589C
45340C
0000000240
45347C
45448C
56092C
1000002162
55880C
401536242830
401536342830
55996C
66798C
75561C
66202C
1000003361
1000001994
75494C
507442830
DESCRIPTION
Stem Bushing
Push Button Assy
Brkt - Conduit Support
Drain Plug
Kit - Regulator/Holder/Nut
Kit - Bubbler/Nipple/Gaskets
Strainer Plate
Basin
Regulator Lever
Pivot Bracket
Regulator Retaining Bracket
Compressor Service Pak
Overload
Relay
Cold Control Assy
Kit - Drain/Gasket/Adapter/Nut/Seal
Gasket
Electrical Box-Cold Control
Kit - Heat Exchanger/Drier
Electrical Box-Power Connection
Tailpipe Assy
Poly Tubing (Cut To Length)
Kit - Union - 1/4 (3 Pack)
Regulator Mounting Bracket
Right Panel
Left Panel
Strainer
Condenser Assy
Elbow - 3/8
Drier - Note: for individual sale & also included in Item #19
Kit - Evaporator Replacement
Kit - Tee - 1/4 (3 Pack)
Check Valve
Front Panel
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE
WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or orders for repair parts MUST include Model No. and Serial No. of
cooler, name and part number of replacement part.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
PAGE 5
0000001091 (Rev. A - 02/16)